Best Robot Mower for Buffalo Grass: Heights and Settings to Check
9 min read · by Laura Kessler · Updated
There is no single best robot mower for buffalo grass, but the sources give a clear height to aim for: 2 to 3 inches on a watered lawn. Colorado State University Extension lists that band and says buffalo grass can be mowed to it or left unmowed. A University of California guide sets the mower lower, at 1 to 2 inches. The mower that suits buffalo grass is therefore one whose cutting-height range reaches that band, so this guide shows which specs to check and how to set one up.
The short answer
- Target height: 2 to 3 inches for a watered buffalo grass lawn, according to Colorado State University Extension, as of 2026-11-11.
- UC mower setting: 1 to 2 inches, mowing when the turf reaches 1 1/2 to 3 inches.
- Minimum for any lawn: 2 inches, per Colorado State.
- Mower range: check the lowest and highest setting in the manual. One Husqvarna model family lists 2 to 5 cm (0.8 to 2 inches).
- One-third rule: never remove more than one-third of the grass height in a single mowing.
What height buffalo grass needs, by source
Two university pages give buffalo grass height directly. They describe it in different ways, so the table separates the mower setting from the height the lawn is kept at.
| Source | Recommended figure | What it means |
|---|---|---|
| UC Healthy Lawns (UC IPM) | Mower set to 1 to 2 inches | Mow when the turf reaches 1 1/2 to 3 inches |
| Colorado State University Extension | 2 to 3 inches, with 2 inches as the minimum for any lawn | Buffalo grass can be mowed to this height or left unmowed |
The two ranges meet at 2 inches. For a closer look at the grass itself, see the best mowing height for buffalo grass. Our reading is that 2 to 3 inches is the target to aim for, and the UC setting shows a lower cut is possible, not required. Colorado State gives the 2 to 3 inch band for bluegrass, ryegrass, fescue and wheatgrass, and says buffalo grass and blue grama can be mowed to that height as well.
Why the mower’s height range matters more than the brand
A robot mower can only hold the target band if its adjustment range reaches it, so the top of the range matters as much as the bottom. For the best robot mower for buffalo grass, the height range is the first spec to read. Husqvarna’s support page for the Automower 305, 310 Mark II and 315 Mark II says the settings run “from a minimum of 2 centimetres (0.8 inches) to a maximum of 5 centimetres (2 inches).” That tops out at about the 2-inch floor, so those models can hold 2 inches but not the upper part of the 2 to 3 inch band.
The height knob moves anticlockwise to raise the cut and clockwise to lower it. Ranges differ between models, so the manual for your exact model is the figure to trust.

- Floor below the band: a model with a 0.8-inch minimum can go well under Colorado State’s 2-inch floor. Our reading is that the lowest setting is not the target; you choose a setting inside the band.
- Ceiling of the range: a model whose highest setting is under 2 inches cannot reach the band, one that stops at 2 inches holds only the bottom of it, and one whose lowest setting sits above 3 inches misses it from the other side.
- Adjustment method: a knob or stepped setting lets you hold one height across the season.
Heads up
Colorado State gives 2 inches as the minimum height for any lawn. A mower that can cut lower is not a reason to go lower, because removing too much leaf in one pass stresses the turf.
The one-third rule limits every robot mower cut
Never remove more than one-third of the grass height in one mowing. UC IPM states it directly: “Only remove one-third of the height of the lawn at a time.” Colorado State gives the same limit, and our guide to the one third rule for mowing grass explains the math. Colorado State asks owners to mow often enough that no more than one-third of the grass height is removed at any single mowing.
- Pick the target. Choose a height from 2 to 3 inches and set the mower to match.
- Work out the trigger. Multiply the target by 1.5 to find the height at which to mow. This is our arithmetic from the one-third rule, not a figure from either source.
- Lower gradually after long grass. Husqvarna advises keeping the highest setting for the first few weeks after a new installation or when the grass is long, then lowering it each week until you reach the height you want.
Watering sets how often the mower runs
Watering changes how fast buffalo grass grows, so it changes how often the mower needs to run. Colorado State says a buffalo grass lawn may need mowing once every 10 to 20 days, depending on how much it is watered.
UC IPM adds that the grass should be mowed frequently in spring and summer, when leaves are actively growing, and less often or not at all in fall and winter, when growth slows or the grass goes dormant. Our reading is that a robot mower’s short, frequent runs fit this pattern, since each run removes only a little leaf. Set the schedule to follow the trigger height and the growing season, not a fixed calendar.
Shade and stressed lawns
Neither page we read gives a shade-specific height for buffalo grass. Colorado State’s note that buffalo grass does well unmowed suggests a stressed lawn can be cut less often, not cut shorter. Our reading is that a shaded or drought-stressed lawn suits the upper end of the band better than 2 inches, because removing leaf under stress slows recovery, but Colorado State still advises one height all year. Because shaded grass gets less light, it may reach the trigger height more slowly, so our reading is to check the lawn after each run rather than rely on a timer alone.
A dormant lawn in fall or winter may need no cut at all, which matches UC IPM’s advice to mow less or not at all in those seasons. Treat that as a reason to skip runs, not to lower the deck. See how often to mow buffalo grass for the frequency side.
Setting up a robot mower for buffalo grass
Set the height first, then the schedule, then check the result after a few cycles. Husqvarna’s steps for these models start by stopping the mower and opening the hatch, then turning the height knob. The same page gives the minimum and maximum settings to check against the target band.

- Confirm the range. Read the lowest and highest settings in the manual for your model.
- Set the target. Choose a setting in the 2 to 3 inch band and keep it there through the season.
- Recheck after a few runs. Measure the grass with a ruler after several cycles and confirm that no more than a third was removed at any cut.
- Hold the height, change the schedule. Colorado State advises mowing at the same height all year, so adjust how often the mower runs, not the setting. Our guide on the best mowing height for a robot mowed lawn covers other grass types.
Best robot mower for buffalo grass: what to check before you buy
This guide does not rank robot mowers, so the best robot mower for buffalo grass here means the one whose specs fit the target height. The sources we read give no independent test data on robot mowers for buffalo grass, so the checks below are based on the target height and on manufacturer specifications. Our reading is that these matter more than any brand name.
- A range that spans 2 to 3 inches: a highest setting of at least 2 inches (about 5 cm), ideally 3 inches (about 7.6 cm), and a lowest setting no higher than 3 inches. A model that misses the band keeps the lawn shorter or taller than the target.
- Stepped or knob height control: you want to hold one height without guesswork.
- Published range for your exact model: the manual gives the minimum and maximum in centimetres and inches.
- Run schedule options: the ability to set fewer runs for fall and winter matches the growing season.
Frequently asked questions
What height should the best robot mower for buffalo grass hold?
Colorado State University Extension gives 2 to 3 inches for a watered buffalo grass lawn, and UC IPM sets the mower at 1 to 2 inches. The band both sources share is 2 inches, so 2 to 3 inches is the safest target.
Can a robot mower cut buffalo grass lower than 2 inches?
Some models can. Husqvarna’s Automower 305, 310 Mark II and 315 Mark II list a minimum of 2 cm (0.8 inches). Colorado State gives 2 inches as the minimum height for any lawn, so going below that is not advised.
How often should a robot mower run on buffalo grass?
Colorado State says a watered buffalo grass lawn may need mowing once every 10 to 20 days. UC IPM says to mow more often in spring and summer and less in fall and winter. Follow the trigger height rather than a fixed calendar.
Can buffalo grass be left unmowed?
Colorado State says buffalo grass and blue grama do well unmowed. Our reading is that this suits a dormant or dry lawn, not one you want to hold at a set height.
Sources
- UC Healthy Lawns: Mowing warm-season grasses (UC IPM): mower setting of 1 to 2 inches, mow-when height of 1 1/2 to 3 inches, the one-third rule, and mowing frequency.
- Lawn Care Basics (Colorado State University Extension): the 2 to 3 inch band, the 2 inch minimum for any lawn, and the 10 to 20 day interval for watered buffalo grass.
- How to adjust the cutting height on Automower 305, 310 Mark II and 315 Mark II (Husqvarna support): the 2 to 5 cm setting range, the height knob, and gradual lowering after installation or long grass.
01Up next8 min readBy YardBest Mowing Height for Buffalo Grass (What Extension Guides Say)Updated Nov 11, 2026
028 min readBy YardHow Often to Mow Buffalo Grass (Schedule and Height)Updated Nov 11, 2026
039 min readBy YardChoosing and Setting Up a Robot Mower for a Yard With Flagstone Walkways Set in GrassUpdated Nov 19, 2026
049 min readBy YardCan a Robot Mower Cut Warm Season Grass? Heights and LimitsUpdated Nov 11, 2026
058 min readBy YardCan a Robot Mower Cut Centipede Grass? Heights and LimitsUpdated Nov 11, 2026
068 min readBy YardWhat Cutting Height Should a Robot Mower Use for St Augustine Grass?Updated Nov 10, 2026