What Is Cut to Edge Distance on a Robot Mower?
8 min read · by Rachel Whitman · Updated
What is cut to edge distance on a robot mower? It is how close the blade reaches toward the lawn boundary, and no single standard number exists. Each manufacturer defines and labels it differently, so the reliable figures come from the mower’s own manual. The published numbers so far range from about 5 to 6 cm for a remaining strip with edge-cutting models, to a fixed 45 mm disc position on one Husqvarna design, and a roughly 10 cm buffer from walls on one Eufy model.
The short answer
- No universal figure: brands use different names, including EdgeCut, Cut-to-Edge and Edge-Cutting Distance, and they do not publish one shared measurement.
- Blade position matters: a centered blade leaves a wider uncut strip along the edge than an off-centre edge-cutting disc does.
- Published examples: Husqvarna lists a fixed EdgeCut disc position of 45 mm (1.77 in). Robomow gives 10 to 20 cm for a centered blade and about 5 to 6 cm for an edge-cutting model.
- The wire matters too: a boundary wire placed too far from an obstacle leaves uncut grass, while one placed too close makes the mower bounce off it.
- Check the app setting: some models expose an edge-cutting distance setting, and some let you switch the edge-cutting function off.
What is cut to edge distance on a robot mower?
Cut to edge distance describes how close the cutting path comes to a boundary, such as a path, a flower bed, a fence or a wall. Some manufacturers use the phrase for a setting, some for a feature, and some for a physical measurement of the blade. Because the term has no shared definition, the safest reading is the practical one: how much grass remains uncut between the mower’s path and the edge you are trying to reach.
In practice, the phrase is most useful when you read a spec sheet or a manual. A figure labelled as an edge-cutting distance may describe the disc, the uncut strip, or the safety buffer kept from a wall, and those are three different things. Ask the maker which one a number refers to before you compare it with another brand.
Our reading: when you compare two models, do not compare their labels. Compare the stated strip width, whether the model has an edge-cutting disc, and whether the setting can be adjusted after installation.
Why does blade position change the edge?
When people ask what is cut to edge distance on a robot mower, most of the answer comes from where the blade sits. Worx explains that models with an off-centered blade disc give a close cut along borders, which reduces manual trimming, while models without one use a standard blade disc and still reduce the need for trimming. Worx does not give a centimetre figure for that border cut in the page we read.
Robomow’s blog describes the same trade-off in numbers. A centered blade, it says, leaves an uncut strip of about 10 to 20 cm at the edge. On a robotic mower with an edge-cutting function, the blade sits to one side under the body and can even extend beyond the wheelbase, and the strip is much narrower. The page gives both about 5 cm and about 6 cm for that strip, so treat the exact figure as a range rather than a spec.

Our reading: the cutting disc is the part that decides how close the mower can reach. A small offset on the disc can change the uncut strip more than a change of software settings.
Which distances do manufacturers publish?
So what is cut to edge distance on a robot mower in actual numbers? Published figures are scattered across manuals and support pages, so it is worth knowing which figure belongs to which feature. Husqvarna’s EdgeCut page gives a fixed disc position of 45 mm (1.77 in) for its edge-cutting disc. That number describes the disc itself, not the distance between the boundary wire and an obstacle.
Eufy’s support article for the E15, E18 and E15 Gen2 gives a different kind of distance. The mower keeps approximately 10 cm from walls and fences to avoid damage, so a thin strip stays uncut. The same article says that grass taller than 9 cm may be identified as an obstacle, and it recommends trimming it below 8 cm with other tools first. It also lists an Edge-Cutting Distance setting in the app that you can adjust when edges are missed.
| Source | What the page states | Type of figure |
|---|---|---|
| Husqvarna EdgeCut | Fixed disc position of 45 mm (1.77 in) | Hardware position |
| Robomow blog | Centered blade: 10 to 20 cm uncut; edge-cutting models: about 5 to 6 cm | Uncut strip |
| Eufy E15/E18 support | Keeps about 10 cm from walls and fences; grass over 9 cm may count as an obstacle | Safety buffer and grass limit |
| Worx Cut-to-Edge wiki | No centimetre figure; off-centered disc models give a close border cut | Qualitative |
How does the boundary wire change the result?
The boundary wire sets where the mower is allowed to go, so its placement can override the edge-cutting disc. Husqvarna says that when the wire is placed farther from obstacles than recommended, more grass remains uncut. Its drive past wire function can be used to reduce that gap. In the opposite case, a wire placed too close makes the mower bounce against the obstacle and perform an EdgeCut.
Robomow adds a practical warning. If the wire is laid directly at the edge, the mower can go beyond it, in some models by as much as 30 cm. The wire therefore marks the inner limit of mowing rather than the outer edge of the cut. Robomow also recommends edging stones about 10 to 24 cm wide, depending on the model, and a margin of about 6 cm to the outermost edges of the lawn.

Our reading: a boundary wire set too close or too far can matter as much as the blade for uneven edges, so check the wire before you change any blade-related setting. For wire layout details, see our guide to laying boundary wire around obstacles.
What should you check before you set up or buy?
Start with the manual for the exact model, because what is cut to edge distance on a robot mower depends on the brand’s own definition. Look for three things: the stated strip width, whether the edge-cutting function is on or off by default, and whether the boundary wire distance is given in centimetres or inches. If the manual gives only a relative setting in the app, note that the number may not be published at all.
- Find the edge feature. Check whether the model has an offset edge-cutting disc, or only a standard blade with an edge-cutting setting.
- Read the wire rules. Confirm the recommended distance from walls, fences and flower beds, and the drive-past-wire option where it exists.
- Plan the margin. Keep the grass below the height the manufacturer lists, and leave a clear strip at the outer edge of the lawn.
- Check the result after installation. If the mower misses an edge or bounces off an obstacle, adjust the app setting first, then the wire, and only then consider manual trimming.
Heads up
Islands are a limit of some systems. Worx states that its Cut-to-Edge feature will not mow the borders of islands in the lawn, so those edges still need hand trimming. For a broader look at models built for close edges, see robot mowers that cut close to edges.
Frequently asked questions
Is there a standard cut to edge distance for robot mowers?
No. When you look up what is cut to edge distance on a robot mower, we did not find a shared standard across brands. Each maker uses its own term and its own figure, so use the number in the model manual.
Is cut to edge distance the same as the boundary wire distance?
No. The blade or disc position controls the uncut strip, while the boundary wire controls where the mower is allowed to go. Husqvarna and Robomow both describe the wire as a separate factor.
Can you change cut to edge distance on a robot mower?
Some models let you adjust an edge-cutting distance in the app, and Husqvarna lets you switch EdgeCut off there. Other changes, such as moving the boundary wire, are done during installation.
Why does my robot mower miss the edge of the lawn?
Eufy lists several likely causes: the wall safety buffer of about 10 cm, cliff or height changes, grass taller than 9 cm, and an edge-cutting distance that is not set well for the lawn. Check those first. Our guide to whether robot mowers trim edges explains what is left for hand trimming.
Sources
- What is EdgeCut and how to use it (Husqvarna): 45 mm disc position, wire distance effects, app on/off setting.
- Cut to Edge and Border Management (Worx): off-centered disc and island limit.
- How cleanly does a robotic mower cut the lawn edge (Robomow): uncut strip widths, wire overshoot, edging stone and margin figures.
- What should I do if my Robot Lawn Mower E15, E18 or E15Gen2 misses cutting the edges of the lawn (Eufy): 10 cm wall buffer, 9 cm grass limit, Edge-Cutting Distance setting.
01Up next8 min readLearnRobot Mower Keeps Getting Stuck on Edges? Causes and FixesUpdated Nov 11, 2026
028 min readLearnWhat Is Edge Cutting on a Robot Mower?Updated Nov 11, 2026
036 min readLearnHow to Trim Edges a Robot Mower Misses: A Hand-Edging GuideUpdated Nov 14, 2026
047 min readLearnWhat Is Edge Mode on a Robot Mower and How Does It Work?Updated Nov 13, 2026
0510 min readLearnWhy does my robot mower turn around before reaching the edge?Updated Nov 19, 2026
069 min readLearnCan a Robot Mower Cut Long Grass? What the Sources SayUpdated Nov 11, 2026