What Is Edge Cutting on a Robot Mower?
8 min read · by Rachel Whitman · Updated
What is edge cutting on a robot mower? It is the ability to cut grass right up to a boundary, such as a wire, wall, fence or flower bed, instead of stopping short and leaving a strip. On a standard centre-blade mower, Robomow puts that uncut strip at about 10 to 20 cm (4 to 8 in). Edge-cut designs narrow it to roughly 5 to 6 cm according to the same source, and the mechanism that does this differs by brand.
The short answer
- What edge cutting on a robot mower means: cutting close to a boundary so less grass is left for a string trimmer.
- Standard centre blade: leaves an uncut strip of about 10 to 20 cm, per Robomow.
- Edge-cut function: Robomow gives about 5 to 6 cm for models with the feature.
- Dedicated edge disc: Husqvarna EdgeCut uses a rear disc at a fixed 45 mm (1.77 in) position and a sweeping turn at the boundary.
- Offset disc: Worx Cut to Edge uses a blade disc set off-centre on supported models.
- Wire decides a lot: the boundary wire placement changes how much grass is left uncut.
What is edge cutting on a robot mower and why the blade matters
On a centre-blade design the cutting disc sits under the middle of the housing, so the wheels and body keep the cut short of the boundary. Robomow describes the strip left along borders with a centre-blade mower as about 10 to 20 cm, and it says this strip is quite large when the blades are centred. Our reading is that the gap comes from where the blade sits, so what is edge cutting on a robot mower depends on the design rather than on a fault in one model.
The strip matters because it is the grass a homeowner must trim by hand. Our reading is that edge cutting on a robot mower is therefore a question of how much of that strip a design removes, not a yes-or-no feature.

Edge cutting on a robot mower with a rear disc: Husqvarna EdgeCut
EdgeCut is a feature that cuts along the lawn edge with a dedicated disc at the rear of the mower. Husqvarna gives the disc a fixed position of 45 mm (1.77 in) for an optimal cutting result. The article does not say what that distance is measured from, so it should not be read as the exact width of the strip left behind.
The feature activates when the mower approaches a physical or virtual boundary. The mower then makes a sweeping turn so the disc cuts along the boundary. Husqvarna says stay-out zones made with AIM Technology do not trigger EdgeCut, while zones made with EPOS Technology do. EdgeCut can be turned off in the app if it is not needed.
| Design | Where the cut sits | Uncut strip (vendor figure) |
|---|---|---|
| Standard centre blade | Blade centred under the body | About 10 to 20 cm (Robomow) |
| Edge-cut function (Robomow) | Models with an edge-cutting function | About 5 to 6 cm (Robomow, two figures on one page) |
| Rear edge disc (Husqvarna EdgeCut) | Disc at rear, fixed 45 mm position | Not given as a strip width |
| Offset disc (Worx Cut to Edge) | Off-centre disc on supported models | Not given in cm or in |
The table shows why the same term, what is edge cutting on a robot mower, can mean different things across brands. Robomow gives a measured strip for its centre-blade and edge-cut designs, while Husqvarna and Worx describe a mechanism without a width you can compare directly. For a buyer, the practical point is to look for a specific figure in the manual or the spec sheet, not to assume that the words “edge cutting” mean a particular distance.
How an offset disc works on Worx Cut to Edge
Worx describes Cut to Edge as a feature that needs an off-centred blade disc. The company says this makes a close cut along borders. Other Landroid models use a standard blade disc and still reduce manual trimming, so the feature is tied to specific models rather than to every unit in the range.
Worx also describes a border cut as a scheduled pass along the lawn perimeter. The Worx wiki says the mower is pre-programmed to mow the perimeter twice a week, and that islands are excluded, so the border cut does not mow their edges. Border cut can be switched on or off per day in the app under Schedule, then Manual Schedule. The page gives no measurement in centimetres or inches for the border.
How the boundary wire changes the result
For a wire-based mower, the wire position sets the outer limit of the mowing area. If you are still planning a layout, our boundary wire installation guide covers the basics, and laying wire around obstacles shows how the line changes near beds and trees. Husqvarna says that if the wire is closer to an obstacle than recommended, the mower bounces against the obstacle and performs an EdgeCut. If the wire is farther away than recommended, more grass remains uncut. Its drive past wire function can reduce that gap, though the article only names the function and does not explain its steps.
Robomow makes a similar point from the other side. It says that with the wire laid right at the edge, some models can travel up to 30 cm beyond it. So the wire is not only a boundary for the mower; it also sets how close the mower gets to the grass you care about. Our reading is that a wire placed carefully, with a clear margin from the obstacle, usually matters more to edge results than the disc design alone.

What edge cutting does not replace
A fair answer to what is edge cutting on a robot mower includes its limits. Edge cutting reduces the strip, but the sources do not describe it as removing every edge a homeowner would trim. Our reading is that spots where grass grows against walls, fences or flower beds, and areas the mower cannot reach, are the likely cases for a string trimmer, and the vendor pages we read do not claim otherwise. Our note on robot mowers and flower beds looks at that edge in more detail.
Robomow also recommends leaving a margin of about 6 cm from the outer edge of the lawn to avoid retouching, and it gives a stone or edging width of approximately 10 to 24 cm depending on the model. The page is not fully consistent: the introduction gives about 5 cm for its edge-cut width, while the edge-cut section gives about 6 cm. That is one reason to read a single brand’s figures with care.
Heads up
Edge cutting is not the same as an island or obstacle feature. Worx says Cut to Edge does not mow the borders of islands, so a bed or tree ring inside the lawn may still need trimming.
What to check before you buy
Once you know what is edge cutting on a robot mower, the most useful checks when you compare models come from the manufacturer’s manual or support pages rather than marketing summaries. Our reading is that the following points tell you more than the phrase “edge cutting” on its own. For the wider decision, see whether robot mowers need a boundary wire and the Learn guides.
- Cutting mechanism: centre blade, offset disc, or a dedicated rear edge disc.
- Stated strip width: a centimetre or inch figure from the vendor, with the measurement point explained.
- Boundary method: wire, wire-free virtual zones, or grass sensing. Edge results depend on which one the model uses.
- Island and obstacle handling: whether the border pass covers islands, and whether you can switch it off.
- Edging width: how wide a stone or border strip the vendor expects before the mower can reach a clean line.
Frequently asked questions
What is edge cutting on a robot mower, and does it trim the grass right to a wall?
Edge cutting means cutting close to a boundary, but not always right to it. Robomow gives about 10 to 20 cm of uncut strip for a centre-blade mower and about 5 to 6 cm for its edge-cut function. Husqvarna describes a mechanism rather than a strip width, so the exact result depends on the model and the wire placement.
Do I still need a string trimmer if my robot mower has edge cutting?
Possibly. Edge cutting narrows the strip, but the vendor pages we read give a remaining width rather than zero, and the strip next to walls, fences and beds is where a trimmer is most often needed. Check the stated width for your model against your own edges.
Is EdgeCut on by default on Husqvarna mowers?
The Husqvarna article says EdgeCut can be turned off in the app if it is not needed. It does not state whether the feature is on by default, so check the app setting for your model.
Why does the boundary wire position affect edge cutting?
The wire sets the outer limit of the mowing area. Husqvarna says that a wire placed closer to an obstacle than recommended makes the mower bounce and perform an EdgeCut, while a wire placed farther away leaves more grass uncut.
Sources
- How cleanly does a robotic mower cut the lawn edge (Robomow): uncut strip widths, edge-cut width, margin and edging widths.
- What is EdgeCut and how to use it (Husqvarna): disc position, boundary trigger, wire placement, AIM and EPOS behaviour, models and on/off setting.
- Cut to Edge and Border Management (Worx): offset disc, perimeter schedule, island exclusion and app setting.
01Up next9 min readLearnRobot Mower Cutting Unevenly: 4 Causes and How to Fix ThemUpdated Nov 11, 2026
028 min readLearnWhat Is Cutting Width on a Robot Mower?Updated Nov 11, 2026
039 min readLearnCan a Robot Mower Run Over a Garden Hose Without Cutting It?Updated Nov 19, 2026
048 min readLearnHow to Adjust Cutting Height After Overseeding With a Robot MowerUpdated Nov 19, 2026
058 min readLearnRobot Mower Keeps Getting Stuck on Edges? Causes and FixesUpdated Nov 11, 2026
068 min readLearnWhat Is Cut to Edge Distance on a Robot Mower?Updated Nov 11, 2026