How to Update Anthbot M5 Firmware: Step-by-Step Guide
7 min read · by Rachel Whitman · Updated
How to update Anthbot M5 firmware most likely comes down to three steps: update the ANTHBOT app, charge the mower on its station, and start Firmware Update from the device menu. That menu path comes from a reviewer’s walkthrough written for the Anthbot Genie, not the M5, and Anthbot’s own support pages did not show a firmware procedure we could read as of 2026-11-12.
A separate review of the M5 LiDAR says only that its firmware update was pushed over Wi-Fi during setup. Treat the menu names below as a guide for how to update Anthbot M5 firmware, and follow the labels in your own app.
The short answer
- Update the app from your phone’s app store, so the firmware screen matches the current app.
- Charge and dock the mower on its station before you start, and keep the Wi-Fi network on 2.4 GHz.
- Open Firmware Update from the device menu in the app, then tap Update.
- Wait for the reboot and, in our reading, reopen the firmware screen to check no update is pending before you map or mow.
Check the ANTHBOT app version first
The first stage of how to update Anthbot M5 firmware is the phone app: update the ANTHBOT app before you look for mower firmware, because the firmware screen depends on the app. A reviewer’s walkthrough says to open your phone’s app store, search for Anthbot, and install any update that is offered. If no update appears, the app is already current, according to the same walkthrough.
The reviewer cited app version 2.1.65 as the version used for the Genie steps. Your version number may differ. Treat that figure as a point of reference, not a required version for the M5.
Get the mower ready before you start
Place the mower on its charging station before you begin, as the walkthrough advises. The M5 LiDAR review lists a 2.5 Ah (45 Wh) battery, about 40 minutes of mowing per charge, and about 60 minutes to charge. Our reading is that a full charge is the safest start when you update, since the walkthrough warns that a battery that runs out mid-install can make it fail.
Wi-Fi matters as well. Anthbot’s FAQ says the robot supports 2.4G Wi-Fi only and does not support 5G. The M5 LiDAR review says the firmware update was pushed over Wi-Fi during setup, so, in our reading, a router set to 5 GHz only could block the update. Check the band setting on your router before you start; if you are still setting the mower up, see how to set up the Anthbot M5.

How to update Anthbot M5 firmware in the app
The menu path in the reviewer walkthrough is short, although it was written for the Genie rather than the M5. Open the app, select your mower, and follow these steps to update the firmware. Menu names on your app version may differ from the walkthrough.
- Open the device. Select your mower in the ANTHBOT app from the device list.
- Open the menu. Tap the menu icon at the top right of the device screen.
- Choose Firmware Update. Pick it from the dropdown menu.
- Tap Update at the bottom of the firmware screen. Our suggestion is to keep the phone near the mower while it runs.
- Wait for the reboot. The mower announces the update, shows a progress indicator, and restarts by itself when it is done.
The walkthrough also says a firmware prompt may appear in the app without you looking for it. If a prompt appears, the same steps apply. Our reading is that you should not turn off the phone or leave the app mid-install, since the walkthrough does not describe what happens if the connection drops.

Confirm the new firmware version
After the reboot, our reading is that you should reopen Firmware Update and check that the app shows no pending update. The walkthrough we read does not describe a confirmation step, and no version number for Anthbot M5 firmware was published in the sources, so the screen itself is the only reference.
Heads up
The step-by-step source describes the Genie’s firmware menu, not the M5’s. If the names on your screen differ, follow the labels in your app and check the M5 user manual before you assume the steps are the same.
What to do if the update fails
A battery that runs out during the update can cause the process to fail, according to the same reviewer walkthrough. If the install stops, charge the mower on its station, restart it, and try the update again from the firmware screen. The walkthrough gives no other failure steps and no retry limit, so the advice for a failed update stays limited to a full charge and a retry. If battery life is the issue, see how long the Anthbot M5 battery lasts.
If the update keeps failing, contact Anthbot support through the product support page, which lists app troubleshooting, device issues and connectivity help. The support center is the place to ask about your specific model and firmware build. Owners hitting other faults can compare notes in Anthbot M5 problems and complaints.
What the sources do not confirm
No Anthbot-issued firmware guide for the M5 was available to read in this research. Anthbot’s support center returned an access error when we tried to open it, and its FAQ and product support pages do not describe firmware. The steps above for how to update Anthbot M5 firmware should be treated as a reviewer’s walkthrough for another model until you match them to your own app screen.
Because that walkthrough covers the Genie, an M5 may label menu items differently. Check the user manual for your exact model before you rely on any step here, and see our general guide on how to update robot mower firmware for the common pattern across brands.
Frequently asked questions
Does the Anthbot M5 update firmware on its own?
The walkthrough says a firmware prompt may appear in the app. The sources read for this guide do not confirm an automatic update schedule for the M5, so check the Firmware Update screen after each app update.
Can I update Anthbot M5 firmware over 5 GHz Wi-Fi?
Anthbot’s FAQ says its robots support 2.4G Wi-Fi only and do not support 5G. Connect the mower to a 2.4 GHz network before you start the update, and check your router’s band settings if the install fails to start.
Do I need to charge the mower before a firmware update?
Yes, based on the walkthrough, which was written for the Genie and says to place the mower on its charging station. A battery that runs out during the install can make the update fail, so charge fully before you start.
Are the steps the same as for the Anthbot Genie?
Not necessarily. The step-by-step walkthrough covers the Genie, while the M5 LiDAR review only says its firmware update was pushed over Wi-Fi during setup. Confirm the menu names in your own app before you follow the steps for how to update Anthbot M5 firmware.
Sources
- Anthbot FAQ (Anthbot): used for the 2.4G Wi-Fi requirement.
- Anthbot M5 LiDAR review (EasyLawnMowing): used for battery, charging time, navigation and the Wi-Fi firmware note.
- Anthbot Genie app and firmware update walkthrough (EasyLawnMowing): used for the app update and Firmware Update menu path.
- Anthbot product support (Anthbot): used to confirm no firmware steps are listed there.
01Up next8 min readLearnHow to Set Up Anthbot M5: Step-by-Step GuideUpdated Nov 10, 2026
028 min readLearnAnthbot App: Connection, Firmware Updates, and Common FixesUpdated Nov 13, 2026
039 min readLearnHow to Update Mammotion Luba 3 Firmware: Versions and StepsUpdated Nov 11, 2026
048 min readLearnHow to Update Robot Mower Firmware: 5 Safe StepsUpdated Nov 11, 2026
059 min readLearnHow Long Does the Anthbot M5 Battery Last?Updated Nov 11, 2026
069 min readLearnAnthbot M5 RTK Station Setup Problems: Causes and FixesUpdated Nov 11, 2026