Robot Mower Leaves Uncut Strips: How to Fix It
7 min read · by Rachel Whitman · Updated
Robot mower leaves uncut strips how to fix: check the boundary wire first, then the cutting height and wet grass, the blades and deck, and the mowing pattern. A centre-blade robot mower commonly leaves a strip about 10 to 20 cm wide along the lawn edge. Many of these gaps come from settings you can change without buying a new mower (our reading), so work through the fixes in order and recheck after each one.
The short answer
- Move the wire: a wire placed too far from the edge leaves grass uncut. On Husqvarna AIM, set the border at least 1.5 m (5 ft) outside the lawn.
- Adjust for wet grass: wait at least 24 hours after rain and raise the cutting height.
- Check the hardware: inspect worn blades and clear grass buildup under the deck.
- Change the pattern: avoid parallel passes that leave edges uncut, and use edge-cut where your model has it.
How wide the uncut strip usually is
A centre-blade robot mower usually leaves a strip about 10 to 20 cm wide along the edge of the lawn, according to Robomow’s edge-cutting guide. That is wide enough to notice when you walk the border, and it grows if the wire sits far from the edge.
Edge-cut models narrow the gap. Robomow gives two figures for its edge-cut function, about 5 cm in one place and about 6 cm in another, and it recommends a margin of about 6 cm to the outermost edge so you do not need to retouch by hand. The same page notes that vegetation growing right up to walls and fences reaches the limit of edge-cut models, so those spots still need a margin.
Fix 1: Move the boundary wire closer to the edge
A boundary wire placed too far from the edge leaves more grass uncut, because the mower turns before it reaches the lawn edge. Husqvarna’s EdgeCut support page describes a rear edge disc in a fixed position of 45 mm (1.77 in) for an optimal cutting result. If the wire sits farther from obstacles than recommended, more grass remains uncut. If it sits closer, the mower bounces off the obstacle and performs an EdgeCut.
On Husqvarna AIM systems, the work area border should be set at least 1.5 m (5 ft) outside the lawn. AIM accuracy is approximately 1 m (3.3 ft), so the stopping point varies. Husqvarna notes that waypoints placed close to the boundary wire can make the mower stop and turn at the work area border instead of at the wire, which can leave grass uncut beside the wire. This guidance applies only to installations with a physical boundary wire.

- Walk the border. Note where the mower turns short of the edge and where grass stands taller than the rest.
- Move the wire in small steps. Shift it toward the edge a little at a time, and keep the distance your model manual recommends.
- Run one cycle. Check the strip before you move the wire again.
Fix 2: Adjust cutting height and wait for dry grass
Husqvarna advises waiting at least 24 hours after rain before mowing, and setting a higher cutting height than usual when the grass is wet. Cutting wet grass too short leads to severe tearing and clumping, and it puts more strain on the mower.
The one-third rule helps when the lawn has grown long. LSU AgCenter calls it a general guideline: never remove more than one-third of the leaf blade height in a single mowing. The same extension page lists recommended mowing heights for Louisiana turf, which are a useful reference point for warm-season lawns.
| Grass type (Louisiana guide) | Recommended mowing height |
|---|---|
| Bermudagrass | 1 to 2 inches |
| Centipedegrass | 1 to 2.5 inches |
| St. Augustinegrass | 2.5 to 3 inches |
| Zoysiagrass | 1 to 2.5 inches |
Heads up
If the lawn has grown well past its normal height, lower the cutting height in stages rather than in one pass. Our reading is that a sudden large cut leaves ragged patches that look like missed grass.
Fix 3: Check the blades and clean the deck
Dull blades and grass buildup under the deck cut poorly. The result can be ragged, uneven patches that look like missed grass, even when the wire is set correctly. Turn the mower off, remove the battery, and inspect each blade for nicks, bends, or dullness before you touch the wire.
Clean the underside of the deck with a stiff brush, because packed clumps reduce airflow and cut quality. Replace blades in the set your model manual specifies, and keep the spares somewhere dry. Our reading is that these checks cost little and should come before any wire change when the strip looks ragged rather than straight.
Fix 4: Change the mowing pattern and edge setting
Parallel mowing patterns can leave edges uncut. Husqvarna’s EdgeCut page says so directly and recommends checkerboard or triangle patterns, which cover the edges from several angles. If the pattern repeats the same lines, switch it and watch the border on the next cycle.

If your model has an edge-cut or edge-disc setting, turn it on and check the manual for the recommended wire distance at the same time. Changing the pattern alone will not fix a wire that is too far out, so treat it as a separate step from Fix 1.
What a robot mower cannot finish alone
Some edges still need a trimmer, even on a well-tuned robot mower. Robomow says edge-cut models reach their limit where vegetation comes right up to walls and fences, so those spots need a margin and sometimes hand work.
Heads up
Models with grass sensors and no perimeter wire rely on bed edging or another barrier for contrast. Robomow states that manual reworking with a lawn trimmer is the only option at those edges.
Keep a string trimmer or edger for the spots next to walls, fences, and tree trunks. Our reading is that this is cheaper than adding a second wire loop to chase a few centimeters of grass.
Robot mower leaves uncut strips how to fix: check after setup
Change one setting at a time, run a few cycles, and check the edge before you change the next one. A clear pattern tells you which fix worked. Wait at least 24 hours after rain before you judge the cut, because wet grass hides the real result.
Keep a short log with the date, the setting you changed, and whether the strip narrowed on the next cycle. Changing the wire and the cutting height in the same week hides which change helped, so a log is worth the two minutes it takes (our reading). If the strip is still there after a clean deck, correct blades, and a wire moved in small steps, the boundary wire and the border settings are the next place to look.
| What you see | Likely cause | First check |
|---|---|---|
| Narrow strip along a wire-side border | Wire too far from the edge | Move the wire in small steps (Fix 1) |
| Ragged, torn patches after rain | Wet grass or cutting height too low | Wait 24 hours and raise the height (Fix 2) |
| Uneven patches across the whole lawn | Worn blades or a clogged deck | Inspect and clean the blades and deck (Fix 3) |
| Uncut lines along a regular pattern | Parallel passes | Switch to a checkerboard or triangle pattern (Fix 4) |
Frequently asked questions
Is some uncut strip normal?
Yes. Robomow puts a centre-blade strip at about 10 to 20 cm, and its edge-cut function narrows it to about 5 to 6 cm. Fix the strip when it is wider than that or looks patchy.
How far from the edge should the boundary wire be?
Follow your model manual. Husqvarna’s EdgeCut disc is fixed at 45 mm, and its AIM border sits at least 1.5 m (5 ft) outside the lawn.
Do I need to wait after rain before mowing?
Husqvarna advises waiting at least 24 hours after rain before mowing, and setting a higher cutting height on wet grass.
Will new blades fix uncut strips?
Only if the blades are dull or damaged. A wire placed too far from the edge still leaves a strip, so check both. This is our reading.
Sources
- How cleanly does a robotic mower cut the lawn edge (Robomow): strip width, edge-cut figures, and the 6 cm margin.
- What is EdgeCut and how to use it (Husqvarna): 45 mm disc position, wire distance, and parallel patterns.
- AIM technology and uncut grass along the boundary wire (Husqvarna): 1.5 m border and about 1 m accuracy.
- Can you mow wet grass (Husqvarna): 24-hour wait and cutting height on wet grass.
- The one-third mowing rule (LSU AgCenter): the one-third guideline and Louisiana mowing heights.
01Up next7 min readLearnIs It Safe to Leave a Robot Mower Charging Overnight?Updated Nov 14, 2026
027 min readLearnWhy Does My Robot Mower Leave Clumps of Grass?Updated Nov 13, 2026
037 min readLearnWhy Does My Robot Mower Leave Stripes in the Lawn?Updated Nov 13, 2026
046 min readLearnWhy Does My Robot Mower Leave Tire Marks on the Dock Area?Updated Nov 13, 2026
058 min readLearnWhy Does My Robot Mower Leave Unmowed Circles Around Trees?Updated Nov 19, 2026
066 min readLearnWorx Landroid Not Docking? Fix the Usual CausesUpdated Nov 10, 2026