Anthbot Replacement Blades: What to Check Before You Buy
7 min read · by Jordan Ellis · Updated
Anthbot replacement blades are sold as sets, and the right set depends on your exact mower model. Retailer kits differ in blade count and screw count, and we did not find a manufacturer blade spec sheet for Anthbot to confirm which kit fits which model.
Check the model number before you buy, count the blades and screws in the kit, and plan to replace the full set together. Blade intervals published by other robot mower brands give a useful baseline for timing.
The short answer
- Match the model: confirm the blade set against your model number before you order.
- Count the parts: kits differ in blade count and screw count, so compare the counts on each listing.
- Use new screws: the brand guides we read treat screws as single-use.
- Replace in sets: one new blade beside worn ones can cut unevenly, so replace the full set together.
How to pick Anthbot replacement blades
Choosing the right Anthbot replacement blades starts with the model. Blade discs and blade shapes are not interchangeable across robot mower lines, so a set listed for one model may not fit another; our guide to robot mower replacement blades that fit your model shows how to check. Eufy’s blade guide says the mower’s product instructions are the final authority for compatible blades and the replacement process, and that advice applies to Anthbot replacement blades as well.
Third-party listings often name Anthbot models in their titles. These are retailer listings, not manufacturer specifications, so treat the model names as a starting point and not as proof of fit.
Before you buy Anthbot replacement blades, check Anthbot’s own store first. Its accessory pages list replacement blades in stainless steel under both the Genie Series and M Series sections, plus a 5-blade disc listed under Genie Series accessories. The store listings do not name the specific models each part fits, and they do not include blade-change instructions. In our reading, the model number on your mower and the part name on the store page should match before you order.

What a replacement kit usually contains
Kit contents vary more than most buyers expect. The table below compares a published example from another brand with what the Anthbot store lists, so you can see what to count before you order.
| Kit | Blades | Screws | What the listing says |
|---|---|---|---|
| Worx Landroid Long-Life blades (WA0789) | 6 | 6 | Stainless steel; listed as compatible with all Landroid models |
| Anthbot store 5-blade disc (Genie Series accessories) | 5 | Not stated | Store listing does not name the models it fits |
| Any third-party kit | Count on the listing | Count on the listing | Not Anthbot-branded unless the listing says so; check model fit |
The Worx long-life blade is a useful reference point. Worx describes it as having two holes so it can be flipped for double the life, while standard blades have one hole for one use. Any listing should be checked for the same design detail before you buy, because hole layout affects how the blade seats on the disc.
How often to replace robot mower blades
Blade life depends on how much you mow, how dense the grass is, and how much debris the blades hit. Brand guides give different timing, so no single number applies to every Anthbot mower. For a broader view, see how long robot mower blades last.
Husqvarna’s support guide says main disc blades typically last 3 to 6 weeks under normal conditions, and EdgeCut disc blades generally last 9 to 12 weeks. Worx advises replacing its Landroid blades every 3 to 4 months. Mammotion recommends changing blades every 3 months or after 150 hours of use, and sooner if cutting quality drops.
Eufy takes a different approach. Its guide says there is no reliable calendar rule for every garden and recommends replacing blades when they become dull, bent, chipped or damaged. Frayed, pale or browning grass tips can signal dull blades, although heat, watering and grass type can also change the colour. In our reading, condition checks on the blades every few weeks in the growing season are a practical middle ground between a fixed calendar and waiting for visible damage.
Screws, tools and fitting the new blade
Use a new screw each time you change Anthbot replacement blades. Husqvarna says to replace screws each time you change blades, and warns that reused screws can leave a blade loose. Mammotion makes the same point in plain terms: do not reuse the old screws with new blades, because they are single-use.
Wear gloves for the whole job. Mammotion calls gloves mandatory because both new and used blades have very sharp edges. Use a manual screwdriver rather than an electric drill, since Mammotion warns that a drill can damage the screw heads or the cutting plate. Husqvarna suggests a flat or cross-tip screwdriver, ideally magnetic, plus a soft cloth and brush for clearing grass and soil from the disc.
Before you put the mower back on the lawn, power it fully off. Mammotion says to press and hold the power button until the mower is completely switched off, and to remove the safety key if your model has one. Turn the mower over only after it is off, and lay it on a soft mat so the cover and sensors are not scratched. The full swap is in our how to change Anthbot blades guide.

Common mistakes when buying Anthbot replacement blades
The most common mistake is buying by price or by a listing title alone. Two sets that look alike can differ in blade count, screw count and disc design, so a cheaper kit may not fit your model at all. Retailer stock can also change, and some listings can show out of stock.
Another mistake is mixing old and new blades. Eufy says a new blade beside worn ones can produce uneven cutting, which is why replacing the full set together is the safer routine. Reusing screws, using an electric driver, and skipping the power-off step are the other errors the brand guides warn about most often. Our guide to robot mower blade screws covers the screw question in more detail.
Heads up
Retailer listings can be out of stock or show a different model than the one in the photo. Confirm the part against your mower’s model number before you order.
Frequently asked questions
Can I use any robot mower blade on an Anthbot mower?
No. Blade sets vary by model and disc design, so Anthbot replacement blades for one model may not fit another. Compare the model number and the disc design with the listing, and follow the mower’s product instructions for compatible parts.
Should I replace only the dull blade?
Eufy recommends replacing the full set together, because a new blade next to worn ones can cause uneven cutting. Replacing a single blade may leave the disc unbalanced and the cut uneven, so check the mower’s manual for the approved approach.
Can I reuse the old screws with new blades?
No. Husqvarna says to replace screws each time you change blades, and Mammotion says the screws are single-use. Reused screws can leave a blade loose, so fit a new screw with each new blade.
Do I need an electric drill to change the blades?
No. Mammotion advises using a manual screwdriver because an electric drill can damage the screw heads or the cutting plate. Work gloves are still required for both new and used blades.
Before you order Anthbot replacement blades, check the model number, count the blades and screws, and compare the disc design with the parts already on your mower. Those three checks prevent most fit problems. If the model number is not clear, the mower’s manual or the brand’s support team is the right source, not a listing title.
Sources
- Anthbot (Anthbot store home page): replacement blade and 5-blade disc listings under Genie Series and M Series accessories; no blade-change instructions and no model fit named.
- Landroid Long-Life Replacement Blades (Worx): kit contents, two-hole design and the 3 to 4 month replacement guidance.
- How and when to change blades on your Automower robotic lawn mower (Husqvarna): main and EdgeCut blade life, single-use screws and tools.
- Mammotion robot lawn mower blade change guide (Mammotion): the 3 month or 150 hour guidance, single-use screws, gloves and power-off steps.
- Robot lawn mower blades replacement (Eufy): condition-based replacement signs and the full-set advice.
01Up next8 min readGearAnthbot Replacement Battery: What to Check Before You BuyUpdated Nov 20, 2026
028 min readGearMammotion YUKA Replacement Blades: What to Check Before You BuyUpdated Nov 20, 2026
038 min readGearDreame Spare Parts: Blades, Battery and What to Check Before You BuyUpdated Nov 12, 2026
049 min readGearDreame Replacement Battery: What to Check Before You BuyUpdated Nov 12, 2026
058 min readGearSunseeker Replacement Battery: What to Check Before You BuyUpdated Nov 19, 2026
066 min readGeareufy E15 Replacement Battery: What to Check Before You BuyUpdated Nov 11, 2026