How to Change Anthbot Blades: Step-by-Step Guide
9 min read · by Jordan Ellis · Updated
How to change Anthbot blades starts with switching the mower fully off, turn it upside down on a soft surface, replace each blade with a new screw, and check that every blade spins freely. Anthbot’s public support pages did not show a blade procedure for its models when checked, so the steps below follow the blade guides that other robot mower makers publish. Your model manual is the final word on part numbers and screw specifications.
The short answer
- Power off: turn the mower off, remove the safety key if it has one, and put on gloves.
- Flip it: place the mower upside down on a clean, soft mat or blanket.
- Swap: remove each blade with its screw, then fit a new blade with a new screw.
- Check: confirm every blade pivots freely before you put the mower back on the lawn.
Before you start: power off and protect your hands
Learning how to change Anthbot blades safely means treating the power-off steps as the most important part, because blade work is the one part of robot mower maintenance where a mistake can hurt you. Husqvarna’s blade guide says to set the mower to OFF and wear protective gloves before you begin. Mammotion’s guide goes a step further: hold the power button until the mower is fully powered down, and remove the safety key if the model has one. Ecovacs also advises covering the LiDAR sensor on its mowers before you work on the blades, so the sensor is not damaged by dirt or a tool.
This applies whether you are learning how to change Anthbot blades for the first time or repeating the job for a new season. Turn the mower upside down only after it is off. Husqvarna recommends a clean, soft surface so the cover is not scratched. Mammotion adds that you should take care not to damage the vision module or bumper sensors, so a soft mat or blanket is the safer choice.

How often to change robot mower blades
How often you need to change Anthbot blades depends on how much you mow, how dense the grass is, and how much debris the blades hit. Brand guides give different intervals, so the table below shows the figures each one publishes rather than a single rule.
| Blade type or brand | Published guidance | Source |
|---|---|---|
| Husqvarna main disc blades | 3 to 6 weeks under normal conditions | Husqvarna support |
| Husqvarna EdgeCut disc blades | 9 to 12 weeks, because they run only while edge cutting | Husqvarna support |
| Mammotion | Every 3 months or after 150 hours of use, sooner if cutting quality drops | Mammotion blog |
| Segway Navimow H1 | Every 1 to 2 months with regular use | Navimow support |
| Segway Navimow Terranox | Every 80 working hours | Navimow support |
| Eufy | No fixed calendar; replace when blades are dull, bent, chipped or damaged | Eufy blog |
Because the intervals differ, the most reliable check is physical, and it should come before you plan how to change Anthbot blades for the next cutting season. If grass tips look frayed or whitened, or the blades show visible wear, Husqvarna says it is time to change them. Its guide also notes that spring sap can build up on blades, so inspect and clean them more often during that season.
Tools you need
You do not need specialist equipment for how to change Anthbot blades, but the right screwdriver makes a real difference. Husqvarna suggests a flat or cross-tip screwdriver, ideally magnetic, along with a soft cloth and a brush for dirt. Mammotion recommends a manual Phillips screwdriver, or the tool supplied with the blade kit, and warns against an electric drill or driver, which “can damage screw heads or, worse, the cutting plate.” Good gloves are the other essential item.
Step by step: how to change anthbot blades
Here is how to change Anthbot blades one blade at a time. The same basic sequence appears in the Husqvarna and Mammotion guides, and it works as a general checklist for changing Anthbot blades on any disc-style robot mower. Follow the order below and do one blade at a time.
- Put on gloves and power off. Confirm the mower is off before you touch the disc.
- Turn the mower upside down on a clean, soft surface.
- Align the skid plate hole. Rotate the skid plate until its hole lines up with the blade screw, as Husqvarna describes.
- Unscrew the old blade. Use the magnetic screwdriver so the screw does not fall into the grass.
- Clean the disc. Brush away grass and dirt, and clear the screw hole. Mammotion also says to remove any old washers stuck to the disc, because a leftover washer can stop a blade from pivoting.
- Fit the new blade with a new screw. Use one blade per screw, and never reuse the old screw.
- Tighten with a manual screwdriver. Mammotion’s guide says to tighten by hand with a manual tool so the blade can still swing.
- Repeat for every blade, then move to the spin check below.
Screws are the part people most often skip when they learn how to change Anthbot blades. Husqvarna says to replace the screws each time you change blades, because worn screws can let a blade come loose during operation. Mammotion is more absolute: screws are single-use, and it warns never to use the old screws with new blades.
Check the blades after the change
The job is not finished until the spin test passes, so treat it as the last part of how to change Anthbot blades. Each blade should swing freely around its screw. Husqvarna says that correctly installed blades pivot easily, and that this is a safety feature, because a blade that hits an obstacle rotates away instead of breaking or jamming. Turn each blade by hand and make sure it moves without effort. This quick test takes a minute and is the simplest way to confirm the job is right.
Heads up
Do not mix blade types, and do not combine new and old blades. Husqvarna warns that mixing blade types can cause imbalance, noise or vibration.
If a blade is stiff after you learn how to change Anthbot blades, check for a leftover washer or a screw that is not seated correctly before you go on. Husqvarna’s guide also notes that the app can track blade use, so after a change you can reset the blade timer in the Automower Connect app, if your model uses that feature.

When to replace the whole set
Replacing the full set is part of how to change Anthbot blades the right way. Mammotion’s rule is that you should replace the full set if any single blade is cracked, bent, heavily worn, or no longer secured correctly. It also advises replacing blades after a hard impact, and checking the screw holes for widening. Knowing when to replace Anthbot blades is easier if you inspect them each time you clean the disc. If new blades still cause heavy vibration after installation, that is a sign to check the fit again rather than keep running the mower.
- Frayed or whitened grass tips, which point to dull edges (Husqvarna)
- Visible cracks, bends or chips on any blade (Mammotion, Eufy)
- Screw holes that look widened or worn (Mammotion)
- Heavy vibration after a clean fit (Mammotion)
Buying the right blades for your Anthbot
Get the parts right before you start how to change Anthbot blades. Buy blades and screws made for your exact model, because the right parts matter more than the brand name. Mammotion notes that each model can have a slightly different cutting disc, which means a blade that fits one machine may not sit correctly on another. The same guide accepts certified compatible parts, so check the fit and the screw size against your model manual before you buy.
Brand blade kits often include the screws as well as the blades. Ecovacs lists a GOAT blade kit with 12 blades and 12 screws for its compatible models, which is a useful reminder to keep spare screws on hand. Anthbot part numbers and the screw specification were not confirmed on its public pages, so before you learn how to change Anthbot blades, use the manual that came with your mower or contact Anthbot support before ordering.
Frequently asked questions
How often should you change Anthbot blades?
Husqvarna gives 3 to 6 weeks for main disc blades under normal conditions and 9 to 12 weeks for EdgeCut blades. Mammotion suggests every 3 months or after 150 hours of use. Check the blades physically before you decide how to change Anthbot blades for the season, because heavy mowing or debris can shorten their life.
Can you reuse the screws when you change blades?
No. When you learn how to change Anthbot blades, use new screws every time. Mammotion says screws are single-use and that old screws should never be used with new blades. Husqvarna says to replace the screws each time, because worn screws can let a blade loosen during operation.
Can you change Anthbot blades with an electric drill?
For how to change Anthbot blades, Mammotion advises against it. An electric drill or driver can strip screw heads or damage the cutting plate. A manual screwdriver gives you control over how tight the screw gets, so the blade can still pivot.
Do you have to replace all the blades at once?
Not always. For how to change Anthbot blades, Mammotion says to replace the full set if any blade is cracked, bent, heavily worn or not secured correctly. Mixing new and old blades can cause imbalance, noise or vibration, so check your model guide before changing only one.
Sources
- How and when to change blades on your Automower robotic lawn mower (Husqvarna): blade life, screw rule, safety steps and spin check.
- Mammotion robot lawn mower blade change guide (Mammotion): replacement interval, manual screwdriver advice, single-use screws and full-set rule.
- Navimow Terranox: how to replace the blades (Segway Navimow): 80 working hours interval.
- Robot lawn mower blades replacement (Eufy): signs that blades need replacing.
- Ecovacs help center FAQ on blade replacement (Ecovacs): gloves and LiDAR cover before blade work.
01Up next9 min readGearHow to Change Dreame Blades: Steps, Timing and ToolsUpdated Nov 19, 2026
027 min readGearHow to Change Sunseeker Blades: Steps, Safety and Replacement TimingUpdated Nov 19, 2026
037 min readGearHow to Change Segway Navimow Blades: Step-by-Step GuideUpdated Nov 19, 2026
048 min readGearHow to Change Eufy E15 Blades: Steps, Parts and SafetyUpdated Nov 10, 2026
057 min readGearHow to Change Worx Landroid Blades in 7 Simple StepsUpdated Nov 19, 2026
068 min readGearHow to Change Robot Mower Blades (Step by Step)Updated Nov 19, 2026