How to Change Dreame Blades: Steps, Timing and Tools
9 min read · by Jordan Ellis · Updated
To learn how to change Dreame blades, switch the mower off, turn it over, and replace each blade with a new one held by a new screw. Dreame’s blog describes its A3 AWD quick-detach blades as coming off by hand with no tools, while screw-mounted disc blades need a screwdriver or a maker tool. Blade parts differ between Dreame models, so the owner’s manual always comes first.
The short answer
- Interval: Learn how to change Dreame blades on a schedule, not only when they fail. Dreame’s blog suggests a fresh set of robot blades every 6 to 8 weeks during the mowing season.
- Power: Switch the mower off fully and turn it upside down on a soft surface before you touch a blade.
- Replace: Fit each new blade with a new screw, one blade per screw, or clip it in if your model is quick-detach.
- Check: Confirm every blade moves freely before you put the mower back on the lawn.
How often to change Dreame blades
Timing matters as much as technique when you learn how to change Dreame blades. Dreame’s blog says robot blades are small and thin, so they wear faster than steel blades, and it recommends a fresh set every 6 to 8 weeks through the mowing season. The same article says to replace them sooner after the mower runs over debris. Our reading is that this works as a starting schedule, which you then adjust to how much your lawn wears the blades.
Other brands publish different figures, which shows how much blade life depends on the design. The table lists each interval from the sources we read.
| Blade type | Interval given | Source |
|---|---|---|
| Dreame robot blades | Fresh set every 6 to 8 weeks in season | Dreame blog |
| Steel mower blades (general, not robot) | About once a year or every 25 hours of cutting | Dreame blog |
| Husqvarna main disc blades | 3 to 6 weeks under normal conditions | Husqvarna support |
| Husqvarna EdgeCut disc blades | 9 to 12 weeks | Husqvarna support |
| Robomow disc blades | Every 2 to 3 months | Robomow blog |
| Robomow star blades | Often once per season | Robomow blog |
Robomow also recommends a visual check about every two weeks, whatever the blade type. Dreame’s blog ties shorter steel blade life to wet grass, sandy soil and buried stones, so a lawn with those conditions may need changes sooner than a table can show.
Signs your Dreame blades need changing
If you see these signs, it is time to learn how to change Dreame blades rather than wait for the next interval. Replace the blades when the cut gets worse, the mower gets louder, or a blade shows damage. Robomow says a significantly worse cutting pattern means it is time for a blade change, and the signs below come from the two brand pages we read.
- Pale or frayed grass tips a day after mowing (Dreame blog)
- Strips the mower seems to have missed, or an uneven finish (Dreame blog)
- Increased noise, which can signal dull blades (Robomow)
- Higher energy use or more charging cycles (Robomow)
- Bends, cracks or gouges along the cutting edge, which call for replacement rather than sharpening (Dreame blog)
Dreame’s blog also says robot blades are generally designed to be replaced as a set rather than sharpened, so a worn set is usually swapped rather than refreshed. Our reading is that replacing the whole set at once keeps the blades wearing evenly, although no source we read states that directly.
Tools and parts you need before you start
Before you learn how to change Dreame blades, gather what the job needs. Most of the job needs only new blades, new screws, gloves and a clean, soft surface. Whether you also need a screwdriver depends on how your blades attach, so check the model before you order parts.
- Replacement blades for your exact model, the first thing to check when you learn how to change Dreame blades. Dreame’s blog lists the A3 AWD Pro with 15.8 inch dual blades and the A3 AWD with one 7.9 inch blade.
- New screws for every blade. Husqvarna says to replace screws each time, because reused screws can loosen.
- Protective gloves. Robomow advises them because the blades are extremely sharp.
- A screwdriver or manufacturer tool, only if your blades are screw-mounted. Robomow says a disc blade usually needs just one of these.
- A clean, soft surface, such as a towel or mat, to rest the mower on. Husqvarna advises this to avoid scratching the cover.
Heads up
Blade size and mount type change from one Dreame model to another, so check your manual before you learn how to change Dreame blades. Read the part number in your manual, or on the parts list for your exact mower, before you buy replacements.
How to change Dreame blades step by step
This section shows how to change Dreame blades one step at a time. Turn the mower fully off before you touch any blade. Dreame’s blog says to disconnect power before blade work, and it adds that the same rule applies before swapping blades on a robot mower. Keep your hands clear of the cutting edge at all times, and work slowly on each blade.

- Power off fully. Use the mower’s power switch or off setting, and confirm its indicator light has gone out before going further.
- Turn it over. Place the mower upside down on a clean, soft surface so the cover is not scratched.
- Remove the old blade. On a screw-mounted deck, rotate the skid plate until its hole lines up with the blade screw, then unscrew the blade. On Dreame’s A3 AWD quick-detach set, the blade comes off by hand.
- Clean the mounting area. Brush away dirt and grass from the mount, then wipe it with a soft damp cloth if needed.
- Fit the new blade with a new screw. Use one blade per screw, and never reuse the old screw.
- Repeat for every blade. Check that each one pivots or spins freely on its screw before you move on.
- Turn the mower upright and test. We recommend watching the first pass on a small patch of lawn for an even cut and any unusual noise.

Quick-detach and screw-mounted blades compared
Dreame’s quick-detach blades swap without tools, screw-mounted disc blades need a fixing tool, and Robomow’s star blades press out in a third way. Knowing which design your mower uses tells you how to change Dreame blades with the right tools, and saves a wasted trip to the parts shop.

| Design | How it comes off | Tools needed | Source |
|---|---|---|---|
| Dreame A3 AWD quick-detach | Unclipped by hand, then a fresh set clipped on | None | Dreame blog |
| Disc blade on a screw | Old screw removed, new blade and new screw fitted | Screwdriver or maker tool | Husqvarna support, Robomow blog |
| Star blade | Press the centre tabs together, then insert until it clicks | Often none | Robomow blog |
Dreame’s blog says the A3 AWD Pro and A3 AWD blades swap the same way, so the quick-detach method applies to both lines it covers and one guide to how to change Dreame blades fits both. We did not confirm the same design on other Dreame models, so treat the method for how to change Dreame blades as model specific until the manual says otherwise.
Check your work and reset the blade count
After you finish how to change Dreame blades, every blade should move freely on its screw. Husqvarna describes that free movement as a safety feature, because a blade that hits a stone or root swings away to protect the mower. You can read the full checks for how to change Dreame blades in Husqvarna’s blade change guide.
Some robot mower apps keep a blade usage counter, which should be reset after you learn how to change Dreame blades. Husqvarna’s Automower Connect app resets it under More, then Statistics, then Blade Usage. We could not confirm a blade counter in Dreame’s app from the pages we read, so check the app menu or the manual before assuming one exists.
Common mistakes to avoid
Most avoidable problems in how to change Dreame blades come from four habits, and each one is covered by a source we read.
- Reusing old screws. Husqvarna says to replace screws each time, because reused screws can cause blades to come loose during operation.
- Mixing blade types. Husqvarna says to use original blades and screws, and not to mix blade types or new and old blades.
- Skipping the spin check. Our reading is that a blade that does not move freely may be bent or fitted wrongly, so check each one before you restart.
- Working with power connected. Dreame’s blog says to disconnect power before any blade work on a robot mower.
Frequently asked questions
How often should I change Dreame blades?
Dreame’s blog recommends a fresh set of robot blades every 6 to 8 weeks through the mowing season, and sooner after the mower runs over debris. Check the blades about every two weeks, as Robomow suggests, and change them when the cut worsens.
Do I need tools to change Dreame blades?
Whether you need tools to change Dreame blades depends on the model. Dreame’s blog says the A3 AWD quick-detach blades come off by hand with no tools. Screw-mounted disc blades need a screwdriver or a maker tool, according to Robomow. Check your manual before you start.
Can I reuse the old screws?
No. Husqvarna says to replace the screws every time you change the blades, because reused screws can loosen and let blades come off during operation. Fit a new screw for each blade when you learn how to change Dreame blades.
Should I change all the blades at once?
Usually yes, when you learn how to change Dreame blades on a full set. Dreame’s blog says robot blades are generally designed to be replaced as a set rather than sharpened. Husqvarna adds that original blades and screws should be used and that new and old blades should not be mixed.
Sources
- How Often to Replace Mower Blades (Dreame): used for the replacement interval, quick-detach blades, A3 AWD blade sizes and power-off advice.
- How and when to change blades on your Automower robotic lawn mower (Husqvarna): used for blade life, step order, screw rule, spin check and the blade usage reset.
- Changing the blades on a robotic lawnmower (Robomow): used for disc and star steps, gloves, replacement intervals and signs of wear.
01Up next7 min readGearHow to Change Sunseeker Blades: Steps, Safety and Replacement TimingUpdated Nov 19, 2026
029 min readGearHow to Change Anthbot Blades: Step-by-Step GuideUpdated Nov 10, 2026
037 min readGearHow to Change Segway Navimow Blades: Step-by-Step GuideUpdated Nov 19, 2026
048 min readGearHow to Change Eufy E15 Blades: Steps, Parts and SafetyUpdated Nov 10, 2026
057 min readGearHow to Change Worx Landroid Blades in 7 Simple StepsUpdated Nov 19, 2026
068 min readGearHow to Change Robot Mower Blades (Step by Step)Updated Nov 19, 2026