Ecovacs GOAT Replacement Blades: Kit, Fit, and Timing
6 min read · by Jordan Ellis · Updated
Ecovacs GOAT replacement blades are sold as a matched kit: Ecovacs lists one A/O series blade kit with 12 blades and 12 screws, compatible with the A3000 LiDAR PRO and O1000 RTK. Check your exact model before you order, replace all blades and screws together, and plan on a check every few weeks because Ecovacs’s kit page lists a replacement frequency of about 4 to 6 weeks.
The short answer
- What to buy: the blade kit that matches your GOAT series, with its own screws.
- Kit contents: Ecovacs lists 12 blades and 12 screws for the A/O series kit.
- Compatibility: the kit page names the A3000 LiDAR PRO and O1000 RTK. Confirm your model before buying.
- Timing: Ecovacs’s listed interval is about 4 to 6 weeks, but wear depends on how often and where you mow.
- Safety: power off, wear gloves, and protect the LiDAR cover before you touch the blades.
Ecovacs GOAT replacement blades: which kit fits
Ecovacs GOAT replacement blades for the A/O series are sold as one package. Ecovacs sells its GOAT blade kit for the A/O series as one package. The product page lists the contents as blades and screws in matching quantities of 12 each, and names the A3000 LiDAR PRO and O1000 RTK as compatible models. The page does not list other models, so if your GOAT is a different series, check the model label or the Ecovacs support page before you order. Readers who want a broader overview can read our general guide to replacing robot mower blades first and then continue with this page. When you are ready for the next step, read our Ecovacs GOAT spare parts overview for more detail.
Our reading is that the safest purchase is the kit that matches your model number and includes its own screws. Mixing blades from different sources, or reusing old screws, can leave a blade loose or unbalanced, and the mower’s cutting performance depends on every blade turning freely.
Protect the LiDAR before you start
Before you open the mower, gather everything you need in one place. Ecovacs’s approach is simple: keep the LiDAR covered, keep the mower on a clean soft surface, and keep the parts in order. A small tray for the old screws makes it easier to see which blade came off where. Beyond this topic, you can also read our Ecovacs GOAT mower overview and verdict for an adjacent part of owning a robot mower.
Ecovacs’s help center advises wearing protective gloves and covering the LiDAR cover before you replace the blades. After you turn the mower over, do not drag it across the ground, because the LiDAR lens can be scratched. This is a small step, but the LiDAR is the part most likely to be damaged during blade work, and a scratched lens is not a cheap fix.

How often to replace Ecovacs GOAT replacement blades
Ecovacs’s kit page lists a replacement frequency of about 4 to 6 weeks for Ecovacs GOAT replacement blades. Treat that as a starting point rather than a rule. A lawn with long grass, dry debris, or sandy soil wears blades faster than a lawn that is mowed often and kept clean. Check the blades every few weeks and look for chips, bends, dull edges, or blades that no longer spin freely. For a closely related angle, see our universal blade options for other robot mowers as well.
Heads up
Replace the Ecovacs GOAT replacement blades as a full set. Changing one blade while the others are worn can leave the cutting height uneven and put extra strain on the motor.
Fit the new Ecovacs GOAT replacement blades
Husqvarna’s support guidance, which covers a different brand but describes the same basic task, is useful for the order of steps. Switch the mower off, turn it upside down on a clean soft surface, and use one new screw for each blade. Check that every blade spins freely after fitting. The same principles apply to GOAT blades: do not reuse old screws, and do not mix blade types. For the next step after this section, continue with our Ecovacs GOAT blade change instructions.


Signs your Ecovacs GOAT replacement blades need changing
Eufy’s guidance for robot mowers says there is no fixed calendar and recommends replacing blades when they are dull, bent, chipped, or damaged. Those signs apply to GOAT blades too. A bent blade can cause vibration, and a dull blade tears grass rather than cutting it, which leaves brown tips and can invite disease.
Do not run the mower with a blade missing or bent. Avoid sharpening thin replaceable blades unless the manual allows it, because that changes their balance.
Test the mower after the change
When the new blades are in and the screws are tight, turn the mower back over and run a short test cycle on a small section of lawn. Watch the cut for an even finish and listen for vibration or rubbing. If you hear a knock or see the cut turn ragged, power off and check that every blade spins freely and every screw is seated. A test cycle is cheap compared with a damaged LiDAR or a bent blade. See our Ecovacs GOAT replacement battery guide for further detail on a connected question.
Keep a note of the date you changed the set. That makes the 4 to 6 week interval on Ecovacs’s page easy to track, and it gives you a record if a later problem needs support.
Frequently asked questions
Do I need to change all Ecovacs GOAT replacement blades at once?
Replacing the full set is the simplest approach. The Ecovacs kit is sold as 12 blades with 12 screws, so a full change keeps wear even across the mower. Mixing old and new blades can leave uneven cutting.
Can I sharpen GOAT blades instead of replacing them?
Check the manual first. Eufy’s guidance advises against sharpening thin replaceable blades unless the manual allows it. Replacement is the safer choice when the edges are chipped or bent.
Does the LiDAR need protection during a blade change?
Yes. Ecovacs’s help center advises covering the LiDAR cover and avoiding dragging the mower after it is turned over, so the lens is not scratched.
Will any blade kit work with Ecovacs GOAT replacement blades?
Not necessarily. Ecovacs’s kit page names specific compatible models. Confirm your exact model before buying, and do not assume that a blade from another series will fit.
Sources
- Blade Kit for ECOVACS GOAT A/O Series (Ecovacs): 12 blades and 12 screws, compatible models, replacement frequency of about 4 to 6 weeks.
- Ecovacs help center FAQ (Ecovacs): gloves, LiDAR cover protection, and no dragging after the mower is turned over.
- How and when to change blades on your Automower (Husqvarna): switch off, soft surface, one new screw per blade, check blades spin freely.
01Up next7 min readGearWorx Landroid Replacement Blades: Pack, Timing, and FitUpdated Nov 20, 2026
028 min readGearHow to Change Ecovacs GOAT Blades SafelyUpdated Nov 19, 2026
038 min readGearEcovacs GOAT Replacement Wheels: What Is Published and What to CheckUpdated Nov 12, 2026
048 min readGearEcovacs GOAT Replacement Battery: What to Check FirstUpdated Nov 19, 2026
057 min readGearHow to Change Sunseeker Blades: Steps, Safety and Replacement TimingUpdated Nov 19, 2026
067 min readGearBest Robot Mower Blade Replacement Kit: What to CheckUpdated Nov 17, 2026