Ecovacs GOAT Spare Parts: What Ecovacs Publishes and What the Warranty Covers
9 min read · by Jordan Ellis · Updated
The Ecovacs GOAT spare part that Ecovacs publishes as a ready-made kit is the blade kit, with 12 blades and 12 screws. The kit lists the A3000 LiDAR PRO and the O1000 RTK Care Kit as compatible. The battery is covered by a 2-year warranty, but the pages read for this guide publish no replacement part number, so match the model before you buy anything.
The short answer
- Published kit: the blade kit, 12 blades and 12 screws.
- Blade interval: about 4 to 6 weeks, according to Ecovacs.
- Battery: 2-year battery warranty; no replacement part number on the pages read.
- Warranty limits: under Ecovacs’s UK terms, wearing parts such as blades, consumables and non-original parts are not covered. US terms were not found.
Which Ecovacs GOAT spare parts are published
Among ecovacs goat spare parts, the only one with a dedicated kit page on Ecovacs’s shop is the blade kit. The page describes it as a set of blades and screws sold together, so the owner does not need to buy each blade on its own. Ecovacs does not publish a separate kit page for the battery among the Ecovacs GOAT spare parts in the pages read for this guide, and the UK warranty page treats the blades as wearing parts rather than as a warranty item.
The table below lists each part that the pages read for this guide mention, what Ecovacs says about it, and where the rule sits. It covers only what is published, so anything not in the table should be checked with Ecovacs support before you buy.
| Part | What Ecovacs publishes | Where the rule sits |
|---|---|---|
| Blade kit | 12 blades and 12 screws; compatible with the A3000 LiDAR PRO and O1000 RTK Care Kit | Ecovacs shop page |
| Blades (wearing part) | Replace about every 4 to 6 weeks | Ecovacs shop page; UK warranty page |
| Battery pack | 2-year battery warranty, except wearing parts such as the blades | Ecovacs UK warranty page |
| Battery replacement part | No part number on the pages read | Check with Ecovacs support |
| Dry batteries, camera brushes, knives | Listed as consumables and excluded from warranty | Ecovacs UK warranty page |
Because the published list of Ecovacs GOAT spare parts is short, the practical question for most owners is not which part to buy but which part the warranty will still cover after a repair. The warranty section below explains that split in more detail.
Blade kit contents and compatibility
The Ecovacs blade kit for the GOAT line is sold as 12 blades and 12 screws. The product page describes it as “Blade*12pcs+Screw*12pcs,” which gives one screw for each blade.
The kit page names two compatible models: the GOAT A3000 LiDAR PRO and the O1000 RTK Care Kit. Ecovacs writes the line as “Compatible with A3000 LiDAR PRO/O1000 RTK Care Kit.” If your mower is a different GOAT model, do not assume the kit fits. Check the model name printed on the unit and the compatibility line on the listing before you order.
- Confirm the model name on the mower matches the compatibility line on the kit page.
- Count the blades and screws in the kit against the number your mower uses.
- Keep the old screws out of the new set, since the kit includes its own.
The kit page does not say whether it is an original Ecovacs part or a third-party part. It is listed on Ecovacs’s own shop, which is the most direct published source for the blade kit. Our reading is that the safest route is the kit that names your exact model, bought from the same channel as the mower.


How often to replace GOAT blades
Ecovacs gives one replacement interval on the blade kit page: “About 4-6 weeks.” That is the only figure published on that page, and it is a guide rather than a hard limit. Blade wear depends on how much the mower runs, how long the grass is, and whether the lawn has sand, stones or debris that dull the edge faster.
Dull blades are a real cost to the lawn, and our guide to the signs of dull robot mower blades shows what to look for. Purdue Extension’s AY-8 publication notes that many lawns are mowed with dull blades, and that dull blades tear grass tips instead of cutting them cleanly. For that reason, our reading is to follow the calendar as a starting point and also check the blades on a regular schedule, since a visibly torn edge or a bent blade is a sign to replace the set sooner.
When you replace the blades, replace the screws at the same time. Ecovacs includes new screws in the kit, so there is no need to reuse the old fixings.
What the warranty covers and excludes
Ecovacs GOAT spare parts fall under three rules in the Ecovacs UK warranty page. That page applies only in the European country where the mower was bought, and the pages read for this guide include no US terms, so US owners should check the warranty that came with their unit. The UK page gives the GOAT robotic lawnmower an extended warranty of three years for the unit. It gives two years for the battery, but with a clear exception: the battery warranty is “with the exception of wearing parts such as the blades.” That split matters because a blade change every few weeks is normal wear, not a warranty claim. For the general picture, see our robot mower warranty guide.
The same page excludes consumable parts. It names “dry batteries, camera brushes and knives” as consumables outside the warranty. It also excludes spare or replacement parts, including consumables, that are “not offered or recommended by Ecovacs Robotics UK Ltd.” In plain terms, a third-party part fitted to a GOAT may fall outside the warranty, even if it fits.
- Covered: the unit for three years and the battery for two years, subject to the exceptions.
- Not covered: wearing parts such as blades, and consumables such as dry batteries, camera brushes and knives.
- Not covered: spare parts that Ecovacs does not offer or recommend.
To make a claim, the warranty page says to keep the original invoice or the cash receipt from the specialist reseller, and to report defects to the Ecovacs service hotline as soon as they appear. Keep both the receipt and the model name with the mower’s paperwork.
Battery pack: warranty route and what to match
For the GOAT battery, the published route is the warranty first, then an authorised reseller or Ecovacs support. The pages read for this guide give the battery an operating range of 0 to 55 C, and the O1000 RTK listing shows 18 V and 4,000 mAh. Those figures are useful for checking a pack, but they do not show that a particular replacement is approved.
Because no part number is published on the pages read, a replacement pack has to be matched to your exact model and serial number, as our Ecovacs GOAT replacement battery guide also explains. Voltage, capacity, connector and model name must all match. Our reading is that a battery bought outside Ecovacs’s own channel should be checked against the warranty exclusion for non-original parts before you pay for it, since a non-original pack can fall outside cover.
Safety steps before you swap a spare part
Ecovacs help material for the GOAT says to wear protective gloves and to cover the LiDAR cover before you replace the blades. Our reading is that the gloves protect your hands from sharp blades and the cover protects the sensor, so both steps belong before the mower is turned over.
- Power off. As a standard precaution, switch the mower off before you touch the blades.
- Cover the LiDAR. Protect the LiDAR cover so the lens is not scratched.
- Wear gloves. Use protective gloves for the whole blade change, such as the cut-resistant gloves for changing robot mower blades we cover separately.
- Use the matched kit. Fit the blades and new screws from the kit that names your model.
The step-by-step blade change is a separate task. If you are about to do it, use our step-by-step guide on how to change Ecovacs GOAT blades, and keep the order above in mind before you turn the mower over.

What to check before buying a spare part
Before you buy any Ecovacs GOAT spare parts, check the exact model, the part list for that model, and the warranty status. Those three checks cover most of the mistakes that owners make with spares.
- Find the model name and serial number on the mower, not only on the box.
- Match the kit or pack to the compatibility line on the listing.
- Confirm the part is one Ecovacs offers or recommends if you want the warranty to stay in place.
- Keep the invoice or the specialist reseller’s receipt with the warranty card.
Prices change often, so this guide does not list them. Compare the kit contents and the compatibility line first, and check the price on the day you buy.
Frequently asked questions
Do I need to change all the blades at once?
The Ecovacs blade kit comes as 12 blades with 12 screws, so the kit is designed to replace the set together. The pages read for this guide do not state a separate rule for changing one blade at a time, so check your model manual before you mix old and new blades.
Will a third-party blade or battery void the warranty?
Among Ecovacs GOAT spare parts, the Ecovacs UK warranty excludes spare or replacement parts that Ecovacs does not offer or recommend. A third-party part may therefore fall outside the warranty, even if it fits. Keep the receipt and check the warranty terms before you fit one.
Is the GOAT battery under warranty?
The Ecovacs UK warranty gives the battery two years, with wearing parts such as the blades excluded. Claims need the original invoice or the specialist reseller’s receipt, and defects should be reported to the Ecovacs service hotline as soon as they appear.
How often should GOAT blades be replaced?
Ecovacs’s blade kit page says about 4 to 6 weeks. That is a guide, so replace the blades sooner if they look torn, bent or dull, since wear depends on how much the mower runs and the lawn conditions.
Sources
- Ecovacs GOAT blade kit (O-series) shop page (Ecovacs): used for the 12 blades and 12 screws, the compatible models and the 4 to 6 week interval.
- Ecovacs UK warranty terms (Ecovacs): used for the unit and battery warranty lengths, the wearing part and consumable exclusions, and the non-original parts rule.
- Purdue Extension AY-8 (Purdue University): used for the point that dull blades tear grass tips.
01Up next7 min readGearEcovacs GOAT Charging Station Cover: What to Check FirstUpdated Nov 20, 2026
028 min readGearBest Garage for Ecovacs GOAT: Size, Clearance and WinterUpdated Nov 11, 2026
038 min readGearEcovacs GOAT Replacement Battery: What to Check FirstUpdated Nov 19, 2026
048 min readGearEcovacs GOAT Replacement Wheels: What Is Published and What to CheckUpdated Nov 12, 2026
056 min readGearEcovacs GOAT Replacement Blades: Kit, Fit, and TimingUpdated Nov 20, 2026
068 min readGearEcovacs GOAT Accessories Worth Buying: A Practical ChecklistUpdated Nov 20, 2026