Robot Mower Replacement Blades: What a Set Includes and When to Swap
7 min read · by Jordan Ellis · Updated
Robot mower replacement blades are the small cutting blades that bolt to the mower’s cutting disc, and most makers sell them as a set with new screws. The intervals brands publish range from about 4 to 8 weeks, and the wear of the blade matters more than the calendar. This guide covers what a set includes, how often to swap it, the signs of wear, why screws get replaced with the blades, and what to check before you buy.
The short answer
- What comes in a set: an ECOVACS GOAT A/O blade kit lists 12 blades and 12 screws.
- How often: ECOVACS lists about 4 to 6 weeks, Mammotion lists every 3 months or 150 hours, and Sunseeker lists 4 to 8 weeks in season.
- Screws: replace them with the blades, because Mammotion says old screws are single-use.
- Sharpen or replace: Sunseeker says replacement is the better option for most robot mower blades.
What robot mower replacement blades include
A replacement set is not just blades. The ECOVACS GOAT A/O blade kit is listed as “Blade*12pcs+Screw*12pcs”, and the maker names the A3000 LiDAR PRO and O1000 RTK Care Kit as compatible models. Mammotion’s blade-change guide describes the same pattern: each blade is fitted with its own new screw, so a set is only complete when the screws come with it.

| Source | What is listed | Interval listed |
|---|---|---|
| ECOVACS blade kit page | 12 blades and 12 screws | About 4 to 6 weeks |
| Mammotion blade-change guide | One new screw for each blade | Every 3 months or after 150 hours of use |
| Sunseeker replacement guide | Blade set, no count listed | 4 to 8 weeks in the growing season |
The table shows why the set matters. Two brands name a count and screws, and the third does not, so compare listings before you assume a set includes everything you need.
How often to replace robot mower blades
Brands give different intervals for robot mower replacement blades, and the right one depends on how much your mower runs and how much grass it cuts. ECOVACS lists about 4 to 6 weeks for its A/O blade kit. Mammotion’s guide suggests changing blades every 3 months or after 150 hours of use, and sooner if cutting quality drops.
Sunseeker’s guidance is seasonal. It suggests replacing blades every 4 to 8 weeks during the growing season, with a calendar reminder about every 6 weeks. It expects the shorter 4 to 6 week end in spring and fall, and a longer 8 to 10 week interval or more in summer heat or winter dormancy.
Our reading is that the interval is a ceiling, not a target. If your lawn is large, heavy with grass, or cut every day, start with the shortest interval a maker lists and check the edges before each swap.

Signs your robot mower blades need replacing
Sunseeker gives a clear rule: replace the blade when “more than a quarter of the cutting edge is visibly damaged or worn smooth.” Nicks, dents, bending, warping, and severe rust that pits the metal also count.

- On the grass: tips look brown and frayed, the cut is uneven, strips are missed, or yellowish streaks appear where grass was bruised rather than cut.
- On the mower: it slows or struggles on slopes, vibrates more, makes a new hum or rattle, or drains its battery faster.
- On the blade itself: a cracked or permanently bent blade, or a screw hole that has widened, means replace it now. Mammotion adds that after abnormal vibration, or when any blade is cracked or bent, the full set should be replaced, and that a hit on a stone or concrete edge calls for a check for micro-cracks.
Sunseeker also suggests a visual check every one to two weeks, and its FAQ advises checking the blades monthly. Knowing when robot mower replacement blades are due is easier from these signs than from the calendar. Our reading is that a monthly look at the cutting edge, done with the mower upside down, catches most of these signs before the grass shows them.
Why you replace the screws with the blades
The screw is part of the blade system, not a spare. Mammotion states plainly: “NEVER use the old screws with new blades-they are single-use.” Each new blade should get a new screw, and the blade should rotate freely around that screw without effort after it is fitted.
- Turn the mower off and lay it upside down. Remove the safety key first if your model has one, wear cut resistant gloves for changing blades, and use a clean, soft mat or blanket. Take care not to damage the vision module or bumper sensors on the underside.
- Clear the disc. Remove old screws one at a time, clean out wet mulch from the screw holes, and remove any old washers stuck to the disc.
- Fit each new blade with a new screw. Check that the blade pivots freely. The full procedure is in our guide on how to change robot mower blades.
Heads up
Mammotion advises against electric drivers for this job, because they can damage screw heads or the cutting plate. Use a manual screwdriver that fits the screw head, and see the torque screwdriver kit checklist if you want a tool to match.
Sharpen or replace a robot mower blade
For most robot mower blades, replacement beats sharpening, so it is worth knowing this before you buy. Sunseeker says these blades are not designed to be sharpened, and that hard-to-balance DIY sharpening can leave a blade out of balance, which causes vibration and motor wear.
Dull blades cause their own problems, and a dull cutting edge is one of the first signs the grass shows. Mammotion notes that a dull blade “doesn’t cut the grass blade; it tears it,” and that it strains the motor and reduces battery life. Our reading is that a spare set on hand is more practical than sharpening the blades you already have.
What to check before you buy robot mower replacement blades
Check these points before you order a set of robot mower replacement blades for your mower:
- The model the maker names. ECOVACS lists its kit for specific models, so match the kit to your mower’s name in its manual rather than assuming a blade fits. Brands publish this differently, as the pages on Husqvarna Automower replacement blades and Sunseeker replacement blades show.
- The count. Compare blades per set, and confirm whether screws are included, since the ECOVACS kit includes 12 screws alongside its 12 blades.
- The listed interval. Note the maker’s interval, then plan your own check based on the wear signs above.
- Whether you will replace the set as a whole. Mammotion advises replacing the full set after abnormal vibration or when a blade is cracked or bent, so a matched set is the safer buy.
Used together, these four checks turn buying robot mower replacement blades from a guess into a short routine.
Frequently asked questions
Are robot mower blades universal?
None of the pages we read for this guide calls a robot mower blade universal. ECOVACS names specific models for its blade kit, so check the model the maker lists for your mower before ordering.
How many blades come in a replacement set?
The ECOVACS GOAT A/O blade kit lists 12 blades and 12 screws. Counts differ by brand and model, so read the listing or manual rather than assuming one count applies to every mower.
Can I reuse the old screws?
No. Mammotion says old screws are single-use and should be replaced with each new blade, so use the new screws that come with the set.
Can I sharpen robot mower blades instead of replacing them?
Sunseeker says robot mower blades are not designed to be sharpened, and that replacement is the better option for most of them. Uneven DIY sharpening can cause vibration and motor wear.
Sources
- ECOVACS GOAT A/O blade kit (ECOVACS): 12 blades and 12 screws, compatible models, about 4 to 6 weeks.
- Mammotion blade-change guide (Mammotion): single-use screws, interval, fitting checks, damage rules.
- When to replace lawn mower blades (Sunseeker): wear signs, seasonal intervals, sharpen vs replace.
01Up next7 min readGearSunseeker Replacement Blades: What Fits, What to Check and When to SwapUpdated Nov 12, 2026
027 min readGearRobot Mower Wheel Replacement: When to Swap and What to CheckUpdated Nov 19, 2026
037 min readGearSegway Navimow Replacement Blades: How to Choose and When to ChangeUpdated Nov 20, 2026
049 min readGearRobot Mower Blade Screws Replacement: When to Change ThemUpdated Nov 19, 2026
059 min readGearWorx Landroid Replacement Battery: Fit, Swap and 1-Year WarrantyUpdated Nov 19, 2026
068 min readGearHusqvarna Automower Replacement Battery: Dealer Swap and LifespanUpdated Nov 19, 2026