Robot Mower Charging Station Anchor Screws: What to Use
7 min read · by Jordan Ellis · Updated
Robot mower charging station anchor screws hold the base to the ground so the mower can dock every time. The manufacturer guides we read say to fix the base with the ground stakes or screws in the kit on soil, and with plugs and screws or expansion bolts on concrete or another hard surface. The pages we read do not give anchor sizes or hole spacing, so match the hardware to the holes in your own station’s base.
The short answer
- On soil: use the ground stakes or screws supplied with the station.
- On concrete or a hard surface: use plugs and screws, or expansion bolts, which Mammotion says are sold separately.
- Before you fix it: level the base, then anchor it. Keep the clear space your model’s manual requires.
- Why it matters: Mammotion warns that if the station moves slightly, the robot may fail to dock correctly.
What holds the charging station in place
A charging station that rocks or slides turns every return trip into a gamble. Mammotion lists the expected result of its install steps as “The charging station is firmly fixed and does not move.” Worx uses the same approach in its Landroid Vision guide, telling owners to secure the station “to the ground using the provided screws and hex key.”
Our reading is that the anchor is the second step, not the first. The ground has to be flat and firm before any fixing goes in, because a base sitting at an angle can hold the anchors under strain and still misalign the mower’s contacts during docking.
Charging station anchor screws and ground stakes on soil
On soil, the fixing the makers name is the hardware in the box. Mammotion’s installation step reads “Secure the station using the included ground stakes,” and its tips section repeats the rule: “Use stakes or expansion bolts to firmly secure the station.” Its items list also names stakes or bolts as needed without saying which ones come in the kit, so count the parts in your box before you start digging.

Worx’s guide points to the same kit-first approach. Its screws and hex key are the fixing the maker supplies for the base, so using them keeps the install within the manual. Keep the boundary wire pegs in a separate pile. Those hold the perimeter wire, and our reading is that they are not a substitute for the station’s own fixings.
Concrete, pavers and other hard surfaces
Ground stakes need soil to grip, so on concrete they are the wrong tool. Mammotion is direct about it: “If installing on concrete, use expansion bolts (not included).” Worx gives the same instruction in different words, saying “If installing on a hard surface, use plugs and screws.” In both cases the anchors are bought separately, so get them before install day.

Neither guide gives an anchor diameter, length or hole depth. Our reading is to read the base-plate hole pattern in your model’s manual, then buy anchors that fit those holes. A patio, paver or garage slab counts as a hard surface for this purpose, and the same rule applies.
Placement comes before anchoring
Choose the spot first, then fix the base. A station that has been anchored and then moved means lifting the fixings and checking the boundary wire again. The clearance numbers differ by brand, so treat the figures below as examples and use your manual.
- McCulloch ROB operator’s manual: at least 3 m (9.8 ft) free in front, 1.5 m (4.9 ft) on each side, a level surface, and a nearby outdoor outlet. It also asks for a spot under a roof, at least 30 cm (12 in) above the ground, and no cutting or extending of the low-voltage cable.
- Mammotion: at least 1.5 m (5 ft) of clear space in front and on both sides.
- Worx Landroid Vision: a 2 m straight path in front and at least 1.5 m clearance behind the station.
Robomow adds that the station should be protected from full sun and splashing water, and should not sit near a lawn sprinkler. Its guide says constant heat shortens battery life, so a shaded or sheltered spot matters to the charger as much as the anchors do.

Why a moving station breaks docking
A loose base is a charging problem, not only a neatness problem. Mammotion warns that “If the station moves slightly, the robot may fail to dock correctly,” and that “Even a small movement or poor placement may affect the robot’s ability to return and charge reliably.” Its guide also says a station that is not level “may cause misalignment during docking.”
Our reading is to check the base after the first few weeks, and again after heavy rain or after the lawn has been dug or re-seeded near the dock. If it has shifted, re-level it and re-anchor before you blame the mower.
What the sources do not tell you
We did not find a source that gives expansion bolt sizes, hole depths or torque for the base. The Husqvarna placement guide says the baseplate must not be bent, which matters when you tighten anything down. The same guide asks owners to keep metal such as rebar, metal edging and coiled low-voltage cable away from the station, because they can disrupt the signal.
For exact fixings, the manual that came with your model is the final word. If the manual is missing, the manufacturer’s support page for your model is the next place to check.
What to check before you buy anchors
Buy only after you know four things: the surface under the base, the hole pattern in the base, what the kit already includes, and how much clear space the manual asks for.
| Check | Why it matters | Where the guides say it |
|---|---|---|
| Surface under the base | Soil takes stakes or screws; concrete takes plugs or expansion bolts | Mammotion, Worx |
| Hole pattern in the base | Sets the anchor diameter and spacing | Your model’s manual |
| Items in the box | Shows whether stakes, screws or a hex key are included | Mammotion, Worx |
| Clear space in front and at the sides | Brands range from 1.5 m to 3 m in front | McCulloch, Mammotion, Worx |
| Outlet and shelter | Keeps the power supply dry and out of direct sun | McCulloch, Robomow |
Frequently asked questions
Can I use the boundary wire pegs to anchor the charging station?
The guides we read name the station’s own ground stakes or screws for anchoring, and plugs or expansion bolts on hard surfaces. None of them lists boundary wire pegs as a station fixing, so check your manual before you substitute anything.
Do I need anchors if the station sits on flat grass?
Yes, if you want the base to stay put. Mammotion tells owners to secure the station with the included ground stakes, which means the maker expects a fixing even on soil.
What if the base will not sit flat?
Mammotion says a station that is not level may cause misalignment during docking. Our reading is to fix the ground before you anchor, rather than shimming under a base that is already fixed.
Does the anchor choice affect the battery?
Not directly. The anchors hold the base in place, while Robomow says constant heat shortens battery life, so a shaded or sheltered spot matters more to the battery than the fixing does.
Sources
- Mammotion charging station installation guide (Mammotion): ground stakes, expansion bolts on concrete, flat ground, 1.5 m clearance, docking misalignment.
- Worx Landroid Vision installation, charging base (Worx): provided screws and hex key, plugs and screws on hard surfaces, 2 m path and 1.5 m rear clearance.
- McCulloch ROB operator’s manual (Husqvarna Group): 3 m front and 1.5 m side clearance, outlet, roof and height, low-voltage cable rules.
- Robomow, how to install the charging station (Robomow): flat ground, protection from sun and sprinklers, battery heat.
- Husqvarna Automower charging station placement guide (Husqvarna): level surface, baseplate not bent, metal kept away.
01Up next9 min readGearRobot Mower Blade Screws Replacement: When to Change ThemUpdated Nov 19, 2026
028 min readGearChoosing the Best Stainless Steel Anti-Theft Ground Anchor for Mower DocksUpdated Nov 19, 2026
037 min readGearRobot Mower Charging Station Extension Cable Outdoor: What to CheckUpdated Nov 19, 2026
048 min readGearSmart Plug for Robot Mower Charging Station: 5 Safe RulesUpdated Nov 10, 2026
057 min readGearRobot Mower Charging Station Base Plate: Setup RulesUpdated Nov 19, 2026
068 min readGearRobot Mower Cover for Charging Station: What the Manuals SayUpdated Nov 19, 2026