Why Does My Robot Mower Spin in Circles? Causes and Fixes
6 min read · by Rachel Whitman · Updated
Why does my robot mower spin in circles? Usually because one drive wheel loses grip, its sensors keep reading a false obstacle, or the boundary signal is broken. Start with the wheels and the underside, then check the boundary wire and the lawn. Most spinning problems are fixed by cleaning and a short reset, and only a few need a parts replacement.
The short answer
- Wheel grip is the most common cause. A stone or worn tread can stop one wheel while the other keeps turning, so the mower pivots in place.
- Dirty sensors send it back and forth. Bump and edge sensors that stick can make it reverse and turn repeatedly.
- Check the wire and the lawn. A crossed, looped or broken boundary wire, or a steep or bumpy patch, can trigger circling.
Wheel grip is the first thing to check
When one wheel slips, the mower turns toward the stuck side and keeps circling. An Eufy blog on the same symptom says a stone caught in a wheel or worn treads can cause this, and it recommends removing the cutting deck, brushing off grass and cleaning the wheels with a small tool. The same page says that cleaning the underside fixes more than half of these cases, which is consistent with what we would expect from a mower that drags clippings into its drive. Circling is one of several erratic behaviors, and typical robot mower problems give a broader map of causes and checks. Poor traction is the first thing to inspect, and what causes wheel slip is covered in more depth in a dedicated guide.
Lift the mower and spin each drive wheel by hand. It should turn freely and without grinding. Then put the mower on grass and push it gently to see whether both wheels grip. If one wheel slips, replace the tread or the wheel before you touch the software.

Dirty bump and edge sensors make it turn back
Bump and edge sensors tell the mower when it has hit something. If one sticks because of mud or grass, the mower can read a wall that is not there and keep reversing and turning. Wipe the sensor housings with a soft cloth and check that the bumper moves freely. Use a soft brush rather than a sharp tool, since the sensors are fragile. Dirty bumpers can send the mower back repeatedly, and stuck on edges and kerbs is a related pattern.

Boundary wire problems can make it loop
The mower follows the boundary signal, so a damaged wire can confuse it. The Eufy guidance lists a wire that crosses itself, forms a tight loop or has a break. To test for a break, pass a small AM radio slowly along the wire. A crackling sound stops at the break, which tells you where to repair. Make sure the wire is buried or pinned flat, and that the charging base sits on level ground away from the edges.
Lawn conditions and slopes can trigger circling
Bumps, holes, wet or very short grass, and steep slopes can all make a mower spin. Eufy’s page mentions slopes above 35% and buried metal as triggers. Level the worst bumps where you can, and mark steep areas with the wire so the mower stays off them. For some boundaryless models, Worx’s official fix for a mower stuck spinning in one spot is to install magnetic strips in the area, so check your model’s guide before you change the setup.
Reset and test before you call support
Turn the mower off, remove the battery for about two minutes, and put it back. Recalibrate the sensors from the maintenance menu and install any firmware update. Then set up a small test zone of about 3 m by 3 m with no obstacles. If the mower runs normally there, the problem is most likely the garden, not the machine. If it still circles, the fault is probably inside the mower, and support is the right next step. Before you contact support, a quick compass calibration for heading problems can rule out a drifting heading as the cause.
Ask what changed before your robot mower started to spin in circles
If you keep asking why does my robot mower spin in circles on a lawn that worked fine last month, start with the calendar. A change in the yard is the most likely trigger in our reading, and the checks below follow the order we would use them.
A simple way to narrow it down is to note when the mower started to circle. If it began right after a firmware update, the reset and recalibration steps come first. If it began after the lawn changed, the wire and the edges are more likely. A short log of the date and the spot makes it much easier to match the spinning to a cause.
Spinning often begins after a change in the yard rather than a sudden fault. A new edging strip, a moved hose, a fresh pile of mulch, or a boundary wire disturbed during planting can all alter the path the mower takes. Walk the lawn and look at the spot where the circling starts. If the spot is always the same, the cause is usually local, such as a bump, an object that triggers the sensors or a wire that now runs through the area.
Weather matters too. Wet grass lowers traction, and a mower that runs straight after heavy rain may slip and turn. Wait for the lawn to dry before you run a test, and keep mowing off the wettest days until the problem is solved. Our reading is that a fault that only appears in wet weather points to traction rather than electronics.
Finally, compare the spinning with the app’s error history, if your model has one. A repeated code linked to a wheel or sensor tells you where to look first. A mower that spins without any code, on a clean lawn, is the case to take to support with a short video and the time and place of the spins.
Frequently asked questions
Why does my robot mower spin in one spot?
Usually one wheel is slipping or a sensor is stuck. Clean the wheels and underside, then test the wheel grip by hand.
Can a boundary wire cause circling?
Yes. A wire that crosses itself, loops tightly or has a break can disrupt the signal. Check the wire with a radio to find a break.
Does a battery reset fix spinning?
Sometimes, because a restart clears a temporary glitch. If the problem returns, look at the wheels, sensors and wire.
When should I contact support?
When the mower still circles on a clean, level test zone after the wheel, sensor and wire checks. Include the model and the error code if one shows.
Sources
- Eufy blog: why a robotic lawnmower goes around in circles (manufacturer, French-language page): wheel grip, sensors, boundary wire, lawn conditions, reset and test steps.
- Worx support: mower is spinning in one spot (manufacturer): recommended fix of magnetic strips; the page gives no cause.
01Up next9 min readLearnWhy Does My Robot Mower Spin Its Wheels When Turning?Updated Nov 19, 2026
028 min readLearnWhy Does My Robot Mower Leave Unmowed Circles Around Trees?Updated Nov 19, 2026
038 min readLearnWhy Does My Robot Mower Beep and Stop Mid-Cut? Common CausesUpdated Nov 14, 2026
046 min readLearnWhy Does My Robot Mower Bump Into Things?Updated Nov 14, 2026
056 min readLearnWhy Does My Robot Mower Stop in the Middle of the Lawn?Updated Nov 14, 2026
066 min readLearnWhy Does My Robot Mower Keep Going Back to the Charger?Updated Nov 14, 2026