Robot Mower RTK Antenna Mount: What to Check Before You Buy
8 min read · by Jordan Ellis · Updated
A robot mower RTK antenna mount is the bracket, pole or post that holds the RTK base station (the RTK base station or reference receiver) steady, with clear sky above it and away from walls, trees and metal. Most setups use one of five mount types: a ground pole or tripod, a fence post clamp, a wall bracket, a roof mount, or no mount at all when the station sits on the ground. The right choice depends on sky view, height and how much the mount can move in wind.
The short answer
- Height and sky view matter most. Yarbo says its base station should sit at least 2 m (about 6.5 ft) off the ground, and Husqvarna’s EPOS support asks for a clear sky view of at least 135 degrees.
- Keep clear of walls and trees. Mammotion’s install page says to keep at least 3 m (10 ft) from any wall or tree.
- Use the maker’s kit where one exists. Wall and roof kits are often specific to one mower series, so check the model name before you buy.
- Check the signal after mounting. Use the app’s satellite and signal readout rather than assuming the mount is right.
What the mount has to do
A robot mower RTK antenna mount has to hold the base station still. The station needs an unobstructed view of the sky and a stable position. Any movement in the mount changes the reference point the mower relies on, so the bracket matters as much as the station itself. The mount also has to keep the station upright and keep the cable from pulling.
In practice that means three jobs: lift the station clear of ground-level obstacles, hold it vertical, and route the cable so it stays protected. A mount that does only one of these well usually causes problems later.
Five robot mower RTK antenna mount types compared
Each option trades height, cost of installation and how much the yard layout limits you. The table below is our reading of the sources in this article, not a ranking of products.
| Mount type | Where it works | What the sources say | Main limit |
|---|---|---|---|
| Ground pole or tripod | Open lawns with no nearby walls | Yarbo suggests a pole or tripod to gain height; the base station should be at least 2 m (about 6.5 ft) off the ground | Must stay 3 m (10 ft) from walls and trees |
| Fence post clamp | Yards with a solid wooden or metal post | No maker in our sources gives a height rule for fence posts | Post sway and fence height may cap sky view |
| Wall bracket | Lawns with a house or garage wall on one side | Mammotion’s wall kit bolts the station to the wall; Husqvarna says the top of the station should be above the wall line | Needs a sound wall and a kit that matches the mower |
| Roof mount | Roofs or other high points for O-shaped, U-shaped or separate lawns | Mammotion says a higher place such as a roof suits O-shaped, U-shaped or separate lawns | Access, weight and the roof itself |
| No mount (ground or network RTK) | Yards with few obstacles, or where a network service is available | Navimow says network RTK needs no local antenna, but availability depends on the postcode (see RTK network service without a base station) | Depends on the service and its coverage |

A robot mower RTK antenna mount wall kit depends on the model
A wall mount is the most common choice for a yard with one house wall along the lawn. It is also where most buyers make a fit mistake. Mammotion’s support material describes a wall or roof location for its station, and the install guide says the pole length is chosen from the width of the eaves. That means the wall kit, the eave width and the pole all have to match.
Kits are model-specific. Mammotion’s store listing for its RTK wall mount kit names the LUBA 2 AWD and YUKA series and says it is not compatible with the LUBA 1 AWD, so a kit bought for one series may not fit another. Read the model name on the kit before you order it, and compare it with the mower you own.
A wall bracket also fixes the station to a surface you may not want to drill. Mammotion’s install page has you drill four holes, fit expansion bolts, and secure the station with four M8 x 50 bolts, so check that your wall can take them before drilling. Confirm the hole size and anchor steps on the maker’s install page.
Placement rules that apply to any mount
Whatever type of robot mower RTK antenna mount you choose, the same placement limits apply. Mammotion’s placement guidance uses a 45-degree line: the station should sit high enough that the angle from the station to the top of nearby walls, roof or trees is about 45 degrees. The same page says to keep the station at least 5 m (16 ft) from large glass walls or large metal objects.
The 3 m (10 ft) rule from Mammotion’s install guide is the simplest check to make in the yard. Measure from the station to the nearest wall and to the nearest tree. If either is closer than 3 m, move the mount before you drill or set the pole.

Heads up
Husqvarna’s EPOS support lists metal fences as a source of interference. A metal fence near a fence post clamp is a reason to move the mount, not to hope the signal holds.
Checking the signal after you mount it
Once the robot mower RTK antenna mount is up and the station is powered, the mower’s app is the quickest check. Mammotion’s install guide says the app shows how many satellites the station receives and the signal strength. Our reading is that you should check the readout again after a few minutes, because a station that has just been moved may need time to lock on. If the signal keeps dropping, why a robot mower keeps losing RTK signal explains the usual causes.
The dome on a robot mower’s body is the mower’s own receiver, not the base station mount. It is shown here so you can tell the two apart in the yard. Do not confuse the mower’s antenna with the mount you are installing for the base station.

What to check before you buy
Use this checklist before you spend money on any robot mower RTK antenna mount, whether a bracket, a pole or a kit:
- Model match. Confirm the kit or mount fits your mower series, not only the brand name.
- Sky view. Stand at the planned spot and look up. Note any tree, roof edge or wall that rises above the line you want clear.
- Distance. Keep at least 3 m (10 ft) from walls and trees, and 5 m from large glass or metal.
- Height. Plan for at least 2 m (about 6.5 ft) off the ground, based on Yarbo’s guidance.
- Cable route. Plan a protected path from the station to the charging station, and keep slack for the cable. Our guide to RTK antenna extension cables covers the checks.
- Signal check. After installation, confirm the satellite count and signal strength in the app.
Frequently asked questions
Does a robot mower RTK antenna mount have to be used?
Not always. Some setups place the base station on the ground, and some use a network RTK service that needs no local base station. Where a local station is used, a mount usually improves sky view and keeps the station stable. Navimow says its network RTK needs no local antenna, but availability depends on postcode.
How high should an RTK base station be mounted?
Yarbo says at least 2 m (about 6.5 ft) off the ground, and Husqvarna’s EPOS support asks for a height of at least 2 m (6.5 ft). Mammotion’s installation pages do not give a single height, so use the maker’s guidance for your model and check the signal in the app.
Can I mount the station on a fence post?
A fence post clamp is one of the mount types in use. Check that the post does not sway, that the fence does not block the sky, and that there is no metal fence close by. None of the makers we read gives a fence-post height rule, so test the signal before you commit to it.
Do I need a kit made for my exact mower?
Our reading is yes, where the maker sells one. Mammotion’s store listing says its RTK wall mount kit is for the LUBA 2 AWD and YUKA series and is not compatible with the LUBA 1 AWD. Check the model on the kit against your mower before you order.
Sources
- Mammotion support: How to Install RTK Reference Station (maker): 3 m (10 ft) from walls and trees, pole length by eave width, wall-mount bolts, app satellite and signal readout.
- Mammotion support: best installation place for the RTK reference station (maker): 45-degree placement rule, 5 m from large glass or metal, roof guidance for O-shaped and U-shaped lawns.
- Mammotion US store: RTK wall mount kit (maker): compatibility wording (LUBA 2 AWD and YUKA series, not LUBA 1 AWD), taken from the listing text shown in search results because the page was rate-limited when we tried to open it.
- Husqvarna support: EPOS wire-free signal issues (maker): 135-degree sky view, at least 2 m (6.5 ft) height, top of station above the wall line, metal fences interfere.
- Yarbo blog: RTK signal in a yard (maker, marketing article): base station at least 2 m (about 6.5 ft) off the ground; pole or tripod suggested.
- Segway Navimow: network RTK (maker): no local antenna needed; availability by postcode.
01Up next9 min readGearBest Roof Mount for RTK Antenna: What to Check Before You BuyUpdated Nov 14, 2026
029 min readGearRTK Antenna Wall Mount Bracket: What to Check Before You BuyUpdated Nov 19, 2026
038 min readGearCable Cover for RTK Antenna Wire: 5 Checks Before You BuyUpdated Nov 19, 2026
048 min readGearBest Weatherproof Enclosure for RTK Base Station: 6 Checks Before You BuyUpdated Nov 13, 2026
0510 min readGearRTK Antenna Extension Cable for Robot Mower: 6 ChecksUpdated Nov 19, 2026
069 min readGearBest RTK Antenna Mounting Pole for Robot Mower: What Decides the ChoiceUpdated Nov 13, 2026