How to Change Sunseeker Blades: Steps, Safety and Replacement Timing
7 min read · by Jordan Ellis · Updated
How to change Sunseeker blades: cut power first, turn the mower over on a soft surface, swap every blade with a new one and a new screw, then check that the blades spin freely. Sunseeker says robotic models need the battery removed before blade work, and the full blade set should be replaced together rather than one blade at a time.
The short answer
- Power off: remove the battery and switch the mower off before you touch a blade.
- Replace the set: change every blade and screw together. Do not mix old and new blades.
- Timing: Sunseeker’s robot guidance is about every 6 to 8 weeks in the growing season.
- Never sharpen: robot blades are designed for replacement, not sharpening.
Before you start: cut power and gather parts
Knowing how to change Sunseeker blades is simple, but it only stays safe if the mower cannot start by accident. Sunseeker’s blade guide says electric and robotic models should have the battery removed to cut power. Husqvarna’s support page adds a second step for its own models: switch the mower off at the keypad or jogwheel before you start.
Gather the parts before you learn how to change Sunseeker blades. You need a full set of replacement blades, a new screw for each blade, protective gloves, a soft towel or mat, and a stiff brush for cleaning the spindle area. Check your model’s owner’s manual for the exact screw type and the location of the skid plate, because the layout differs between Sunseeker models.
Step-by-step: how to change Sunseeker blades
The steps below show how to change Sunseeker blades on the common disc-blade design. Work slowly, and keep every screw in a tray so none get lost in the grass.
- Power off and remove the battery. Confirm the mower cannot start before you move on.
- Turn the mower upside down. Place it on a clean, soft surface so the cover does not scratch. Husqvarna gives the same advice for its robot mowers.
- Line up the skid plate. Rotate the skid plate until its access hole lines up with the screw for the blade you are changing.
- Remove the old blade and screw. Unscrew the old blade and set the screw aside for disposal, not for reuse.
- Clean the mounting point. Brush off grass and dirt with a stiff brush, then wipe with a soft damp cloth if needed.
- Fit the new blade and screw. Seat the new blade, follow any markings on the blade, and tighten the new screw to the manufacturer’s specified torque. Use one blade per screw.
Repeat the steps for every blade, and once you know how to change Sunseeker blades, the job gets faster each season. When all blades are installed, turn the wheel by hand to make sure each blade spins freely without rubbing the deck. Put the mower upright, reconnect the battery, and run a short test in the yard before leaving it to mow unattended.

Parts and rules: replace the full set, not one blade
Robot blades are sold and designed as a set, and Sunseeker says the set should be replaced together. That rule matters most the first time you learn how to change Sunseeker blades. The blades are small, hardened and balanced as a group, so one new blade next to worn ones can change the balance of the cutting disc.

Husqvarna gives the same advice and adds two more rules. Replace the screws every time you change the blades, because reused screws may let a blade work loose during operation. Do not mix old and new blades, since uneven weight can cause vibration and noise.
Blade design also changes how often you work on the mower. Robomow explains that disc blades, which use movable blades on a single disc, wear faster than star blades. Its guidance is to replace disc blades every 2 to 3 months, while star blades often last only once per season. Robomow also recommends a visual inspection about every two weeks, and it advises using new screws each time rather than the old ones.
Tighten the screws only until the blades can still move freely. Robomow warns against over-tightening, so check that each blade spins without binding before the mower goes back on the lawn.
- Replace the whole set rather than one blade.
- Use a new screw for every blade.
- Do not sharpen robot blades. Sunseeker says they are made for replacement.
When to replace Sunseeker blades
Sunseeker’s robot guidance says the blades should be replaced roughly every 6 to 8 weeks in the active growing season. Its general blade guide gives a wider range of 4 to 8 weeks, so the two figures are close rather than identical. Knowing when to change Sunseeker blades matters as much as knowing how to change Sunseeker blades. The table below combines the Sunseeker figures with the Husqvarna interval for comparison, which helps you plan how to change Sunseeker blades each season.

| Situation | Suggested interval | Source |
|---|---|---|
| Active growing season, robot guidance | About 6 to 8 weeks | Sunseeker robot blade guide |
| Peak spring and fall (general) | 4 to 6 weeks | Sunseeker Elite blade article |
| Slower summer and winter (general) | 8 to 10 weeks or more | Sunseeker Elite blade article |
| Husqvarna main disc blades, normal conditions | 3 to 6 weeks | Husqvarna support |
Sunseeker’s wear rule is simple: replace the blades when more than a quarter of the cutting edge is visibly damaged or worn smooth. Its Elite article suggests setting a calendar reminder every 6 weeks and doing a visual check every 1 to 2 weeks. Husqvarna notes that spring sap buildup can make blades dirty and sticky, so check them more often at that time.
Common mistakes to avoid
Most problems when people learn how to change Sunseeker blades come from skipped steps rather than hard work. The mistakes below are the ones the manufacturer guides warn about.
- Skipping the power-off step. The battery should be removed before any blade is touched.
- Reusing screws. Husqvarna says reused screws may let blades come loose.
- Mixing blade ages. Old and new blades together can cause vibration and noise.
- Trying to sharpen. Robot blades are designed to be replaced.
Frequently asked questions
How long does it take to change Sunseeker blades?
Sunseeker’s general guide says most homeowners can finish a blade swap in about 15 to 30 minutes. That guide covers push mowers, so a robot mower may take a little longer while you work around the deck and skid plate.
Can I sharpen Sunseeker robot blades?
No. Learning how to change Sunseeker blades is quicker than sharpening them, because Sunseeker says robot blades are designed for replacement rather than sharpening. Replace the full set when the edges are worn or damaged, following the same steps for how to change Sunseeker blades.
Do I need to replace the screws too?
Yes. Husqvarna advises replacing screws each time blades are changed, because reused screws may let a blade loosen during operation. When you learn how to change Sunseeker blades, buy the new screws with the blades.
How do I know when Sunseeker blades are worn?
Sunseeker recommends replacing them when more than a quarter of the cutting edge is visibly damaged or worn smooth. Check every one to two weeks during the growing season, so you can learn how to change Sunseeker blades before they cut poorly.
Sources
- Sunseeker: How to replace your lawn mower blade (manufacturer): battery removal on robotic models, full-set replacement, and the quarter-edge wear rule.
- Sunseeker Elite: When to replace lawn mower blades (manufacturer): seasonal intervals and the reminder schedule.
- Robomow: Changing the blades on a robotic lawnmower (manufacturer): disc versus star blade lifespan, two-week inspection, and new screws each time.
- Sunseeker Elite: How to replace mower blade (manufacturer): torque guidance and the 15 to 30 minute time estimate for general mowers.
- Husqvarna support: How and when to change blades on your Automower (manufacturer): power-off steps, one blade per screw, replace screws, and 3 to 6 week interval.
01Up next9 min readGearHow to Change Dreame Blades: Steps, Timing and ToolsUpdated Nov 19, 2026
028 min readGearHow to Change Eufy E15 Blades: Steps, Parts and SafetyUpdated Nov 10, 2026
036 min readGearEcovacs GOAT Replacement Blades: Kit, Fit, and TimingUpdated Nov 20, 2026
047 min readGearWorx Landroid Replacement Blades: Pack, Timing, and FitUpdated Nov 20, 2026
059 min readGearHow to Change Anthbot Blades: Step-by-Step GuideUpdated Nov 10, 2026
067 min readGearHow to Change Segway Navimow Blades: Step-by-Step GuideUpdated Nov 19, 2026