Robot Mower for a Lawn With a Narrow Side Gate: Width Rules
7 min read · by Laura Kessler · Updated
A robot mower for a lawn with a narrow side gate can get through only if the clear opening is wider than the mower’s body and the manufacturer’s minimum passage width. Navimow’s support lists 100 cm of width and 40 cm of height for a passage, fence or small gate on its i2 AWD, and Husqvarna’s boundary-wire guidance gives 60 cm with a guide wire and 2 m without one. Measure the gate first, then check the figure in your own model’s manual, because the numbers vary by brand and drive type.
The short answer
- Measure the clear width for your robot mower for a lawn with a narrow side gate, between the gate post and the fence or wall, not the gate’s marked size.
- Compare with the manual: Navimow i2 AWD guidance is 100 cm wide and 40 cm high for a passage or small gate.
- Know the drive type: Husqvarna’s boundary-wire guidance asks for 2 m without a guide wire, and says AWD models such as the 435X AWD and 535 AWD should use 2 m for a good cutting result.
- Keep a clearance margin on both sides of the mower’s track, so the mower does not clip the post.
- Do not rely on a gate to be the only route to the dock. Keep the charging path clear.
Why a side gate is harder than an open lawn
A robot mower for a lawn with a narrow side gate faces a fixed opening between two hard edges, usually a post and a fence, and it often has a step or threshold at the bottom. A robot mower treats it as a narrow channel. Navimow’s guidance says that if the opening is narrower or lower than the minimum, the mower “may have difficulty passing through or could become stuck.” That is the failure to plan for: the mower keeps trying the gap and wears its wheels or stalls on the threshold. Interior gates add another constraint to the layout, which using a gate between lawn zones describes.
A narrow gate also tends to leave the mower with a tight turn at each end. Our reading is that the turn, not the straight run, is what usually catches a mower, so the width needed is more than the gap alone.

Robot mower for a lawn with a narrow side gate: check the minimum width
Start with the number in your model’s manual for a robot mower for a lawn with a narrow side gate, not a general figure. Navimow’s support article gives 100 cm of width and 40 cm of height for a passage, fence or small gate, and says these dimensions let the mower move through “comfortably without obstruction.” Husqvarna’s boundary-wire guidance is different. It gives 60 cm between the boundary wires when a guide wire runs through the passage, and 2 m when there is no guide wire, with the note that AWD models such as the 435X AWD and 535 AWD should use 2 m for a good cutting result.
| Source | Setup | Figure |
|---|---|---|
| Navimow i2 AWD support | Passage, fence or small gate | 100 cm wide, 40 cm high |
| Husqvarna Automower support | Boundary wire with guide wire | 60 cm (24 in) between wires |
| Husqvarna Automower support | Boundary wire without guide wire | 2 m (6 ft 6 in) |
The figures do not match because they describe different systems. A boundary-wire passage is set by the wires, while a wire-free mower relies on its own navigation and its map. For a wire-free gate, use the model’s own number and add a margin.
Heads up
Husqvarna’s passage guidance says that with a guide wire, the passage should keep at least 30 cm (12 in) from the boundary wire. Use that as a reminder that the path needs room on both sides, not only the centre.
Measure the gate and the approach
Measure the clear width at three points: the bottom, the middle and the top of the gate, since a post or latch can narrow the gap higher up. Then measure the approach on each side. A gate with a wide opening but a tight turn right before it can still trap the mower. Note the height too, because a low gate frame, a rain gutter or a hanging branch can be the limit. The narrowest gaps are covered in two-foot gaps and robot mowers, along with what the sensors need to pass.
- Take three width readings at the bottom, middle and top of the gate opening.
- Check the approach for a turn or a corner within a few metres of the gate.
- Compare with the manual for your model and drive type.
- Test the route by pushing the mower through by hand, then by letting it run one pass.
What to do when the gate is too narrow
If the gate falls short, you have three options. You can widen the gap by moving a post or swapping the latch, which is often the cheapest fix. You can cut the gate’s edge strip by hand, leaving the gate itself as a no-go zone. Or you can choose a smaller mower, which helps only if the manual’s minimum is the limit and not the drive system. Husqvarna’s support notes that if the mower gets stuck in a passage, you can adjust the corridor width, which is a reminder that the passage is a setting you can change, not only a fixed number. Lawns lined with hedges often have narrow gates, and long hedge-lined yard mower picks looks at those layouts. A gate is often the only connection between front and back, as connecting lawns around a house explains.

Our reading is that a gate with a threshold or a raised step is the riskiest case, because the mower can high-center on it even when the width is fine. Check the threshold height against the manual’s figure and remove any lip that stands above the ground.
Related reads: Layout limits for slim lawns are covered in long narrow lawn feasibility, including turning space and wire spacing. For paths that are just wide enough, side passage mower choices lists candidate models and their clearance limits.
Frequently asked questions
How wide does a gate need to be for a robot mower?
It depends on the model. Navimow’s i2 AWD support lists 100 cm of width and 40 cm of height for a passage or small gate, while Husqvarna’s boundary-wire guidance gives 60 cm with a guide wire and 2 m without one. Use your own model’s manual for the final figure.
Will a robot mower get stuck in a narrow gate?
It can. Navimow’s support says a passage that is narrower or lower than the minimum may leave the mower struggling to pass or stuck. Measure first, and test the route by hand before you rely on it.
Does a guide wire change the gate width I need?
Yes, for boundary-wire systems. Husqvarna lists 60 cm between the wires with a guide wire, and 2 m without one. Wire-free mowers follow their own map, so check the model’s manual instead of applying the wire figures.
Can a robot mower for a lawn with a narrow side gate still work?
Yes, if the gate is wide enough for the model’s minimum, or if you mark the gate area as a no-go zone and keep the mower on the open lawn. The mower’s dock and charging path must stay clear either way.
Sources
- Navimow support, how much space the i2 AWD needs to pass a channel (manufacturer): used for the 100 cm width and 40 cm height figures and the stuck-in-passage warning.
- Husqvarna support, how to create a passage in a boundary-wire installation (manufacturer): used for the 60 cm and 2 m figures and the 30 cm guide-wire clearance.
01Up next8 min readBy YardRobot Mower for Narrow Side Yard Passages: What Widths Work?Updated Nov 11, 2026
028 min readBy YardHow Narrow Can a Robot Mower Passage Be? Simple 2026 RulesUpdated Nov 11, 2026
0310 min readBy YardChoosing a Robot Mower for a Yard with a Metal Chain-Link Gate GapUpdated Nov 19, 2026
049 min readBy YardWhat Is the Minimum Passage Width for a Robot Mower?Updated Nov 11, 2026
059 min readBy YardCan a Robot Mower Work in a Yard With a Gate Between Zones?Updated Nov 11, 2026
066 min readBy YardBest Robot Mower for a Yard With a 3 Foot Side Passage: What to CheckUpdated Nov 13, 2026