What Is Spot Mowing on a Robot Mower and How Does It Work?
7 min read · by Rachel Whitman · Updated
What is spot mowing on a robot mower? It is a mode that cuts a small area of long or missed grass in tight spirals, then returns the mower to its normal mowing routine. Some Husqvarna Automower models start it by hand, placing the mower at the patch and choosing the mode on the keypad. Others switch to a spiral pattern on their own when the cutting disc senses taller grass.
The short answer
- Purpose: clear a patch of long grass that the regular pattern has missed or cannot reach well.
- Manual version: you place the mower at the patch, select spot cutting on the keypad, and close the hatch.
- Automatic version: spiral cutting starts when sensors detect taller grass, with a sensitivity setting you can adjust.
- Limits: availability depends on the model, and the feature works best with an irregular mowing pattern.
What is spot mowing on a robot mower within the routine
Spot mowing is a short, focused job. The mower does not change how it covers the whole lawn. It runs a tight spiral over one patch, then goes back to the regular pattern. Husqvarna describes the manual version this way: the mower mows in tight spirals and automatically resumes mowing afterward. The return to normal routine is what separates spot cutting from a general change of settings. Spot cutting sits on top of the normal routine, so setting up a weekly mowing schedule is a useful companion read.

The idea is simple, but the reason it helps is that a spiral reaches the same patch from many angles. A straight pass can flatten a clump on one line and leave the rest standing. A spiral keeps working the same area until the grass is down, which is why it suits a dip or a bed corner that has grown ahead of the rest of the lawn.
How the manual spot cutting mode works
Husqvarna’s guidance for manual spot cutting is a clear sequence. You place the mower in the high-grass area, press Start on the keypad, select the Spot cutting mode, and close the hatch. The mower then cuts in a spiral and returns to normal mowing when it is done. The mode works in both the main and secondary areas, which makes it useful for a patch that sits in an outlying section.
Our reading is that the manual mode is worth using after a holiday, a dry spell, or a missed week, when one patch has grown much faster than the rest. Running it on a schedule is less useful, because the regular pattern will usually keep the rest of the lawn even on its own.
How automatic spiral cutting decides when to start
Automatic spiral cutting is a different approach. The cutting disc sensors detect when the mower enters higher grass, and the mower switches to a spiral pattern without you doing anything. Husqvarna lists five sensitivity levels, from very low to very high, and higher settings trigger spiral cutting more often. The feature runs only in the main area mode and does not start in the secondary area. Spiral starts affect coverage numbers, and how mowing efficiency is judged explains the measure behind them. The mower decides where to begin a spiral using route logic, which is explained in how robot mowers choose where to cut.
There are limits to the automatic version. Husqvarna says it does not start on slopes steeper than 17 percent, and it works only with an irregular mowing pattern rather than a systematic one. The same guidance warns that frequent triggering can mean the lawn is not being mowed often enough, so the cutting schedule may need adjusting.
Patches, corners, and why they get missed
Missed grass often sits where the regular pattern cannot reach easily. Mammotion’s guide on irregular lawns says that straight, parallel passes can leave grass uncut at inside corners, such as on L- or U-shaped lawns. The risk rises with the number of inside corners: low on rectangular or rounded lawns, moderate with one corner, and higher with two or more. Corners and borders are the other common weak spot, and how edge cutting handles corners covers the usual fix. Missed patches also relate to blade swath, which cutting width and coverage per pass puts in context. Patches near the boundary are often handled by a different feature, and how edge mode cuts along the boundary is covered separately.
The same guide separates two causes. A patch next to an inside corner points to the route, and it suggests a perimeter pass or adaptive route planning. A patch at a dip or uneven ground may come from the mower’s sensors reacting to a change in level, so check whether the mower stops or steers away at that spot. Spot mowing treats the symptom, while a route change fixes the cause.

When spot mowing is the right tool
Spot mowing suits a small, defined patch. It is less suited to a large area that is consistently too long, because the real issue is usually the mowing schedule or the cutting height. If the same patch keeps needing spot cutting, check the boundary, the mowing pattern, and whether the mower is passing that area at all. A second tool for awkward areas is zone mowing, which is described in how zone mowing divides the lawn. Whether patches are missed often depends on run time, as covered in how often a robot mower should run.
Heads up
Spot cutting uses the same cutting disc as the regular pattern. Keep hands and feet clear, lift the mower only with the power off, and check the patch for toys, hoses, or stones before starting.
Before starting a spot job, walk the patch and look for the cause. A bare spot with long grass beside it may be a shaded area the mower rarely reaches, while a patch on a rise can be a slope issue. Note how often the spot needs help. A patch that needs cutting every week points to a route or height problem, which spot mowing will not solve on its own.
Frequently asked questions
Do all robot mowers have spot mowing?
No. Husqvarna says manual spot cutting is only on Automower models with a keypad, and it is not available on NERA models or the 435 AWD. Check the manual for your model before assuming the mode exists.
Does spiral cutting start by itself?
On models that support it, yes. The cutting disc sensors detect taller grass and the mower switches to a spiral pattern. You can adjust the sensitivity, and it works only in the main area mode.
Why do patches of grass keep getting missed?
Mammotion notes that inside corners on irregular lawns can leave grass uncut when the mower runs straight passes. A dip or uneven ground can also trigger sensors and change the route. Adjusting the route or adding a perimeter pass often helps more than repeated spot cutting.
Can spot mowing replace a regular mowing schedule?
No. It is a short job for one patch. If the same area needs it often, the mower is not covering that spot in its regular pattern, and the schedule or route is the better place to fix it.
Sources
- Understanding Automower spiral and spot cutting (Husqvarna): manual spot cutting steps, automatic spiral cutting, sensitivity, slope and pattern limits.
- How to choose a robot lawn mower for an irregularly shaped lawn (Mammotion): inside corners, patches versus dips, perimeter passes.
01Up next7 min readLearnWhy Does My Robot Mower Start Mowing at the Wrong Time?Updated Nov 13, 2026
028 min readLearnCrabgrass Control With a Robot Mower: What Mowing Height DoesUpdated Nov 12, 2026
037 min readLearnRobot Mower Stuck in the Same Spot? Causes and FixesUpdated Nov 11, 2026
047 min readLearnWhat Is Edge Mode on a Robot Mower and How Does It Work?Updated Nov 13, 2026
057 min readLearnHow Does LiDAR Work on a Robot Mower?Updated Nov 14, 2026
067 min readLearnDoes a Robot Mower Work With a Dog in the Yard?Updated Nov 11, 2026