Sunseeker S4 App: Fixing Offline and Pairing Problems
7 min read · by Rachel Whitman · Updated
Most Sunseeker S4 app problems trace back to three things: a router that is not on 2.4 GHz, a phone and mower that are on different networks, or missing Bluetooth and location permissions on the phone. Check those three before you try anything more drastic. Sunseeker’s other models, such as the V3, may use a similar setup, so the same checks can help there too, though the screens can differ.
The short answer
- Router band: the mower needs a 2.4 GHz network, so confirm your router runs that band.
- Same network: the phone and the mower must be on the same Wi-Fi network during setup.
- Permissions: give the app Bluetooth and location access on the phone.
- Close range for pairing: keep the phone within about 1 metre of the mower when you pair over Bluetooth.
- Power cycle and re-add: if the mower shows offline, turn the main power switch off for 30 seconds, then add it to the app again.
Why the Sunseeker S4 app cannot reach the mower
When the S4 app says the mower is offline or cannot connect, the cause is usually on one of three sides: the router, the phone, or the mower’s own connection. Sunseeker’s support material points to the same first checks, and they are worth doing in order because each one rules out a group of causes. If you want the wider context first, start with our mower app cannot connect basics before returning to this page. If this point matters for your setup, read our phone control options for robot mowers for more detail on it.
Start with the router. Sunseeker’s Wi-Fi support article says the router needs to run on 2.4 GHz. Many home routers combine 2.4 GHz and 5 GHz under one name, so check the band settings instead of assuming the network supports both. If the mower never shows up during setup, a 5 GHz-only network is a likely reason.

Wi-Fi setup and the same-network rule
During setup, the phone and the mower need to be on the same network. Some Sunseeker manuals say that an iPhone can only hand the mower a network that the phone is already joined to, so connect the phone to the target Wi-Fi first and then start the setup. If you are switching routers, the mower’s stored network can go stale, and the cleanest fix is to set it up again on the new network. For a closely related angle, see our robot mower Wi-Fi setup explained as well.
The mower’s Wi-Fi light is a quick status check. Sunseeker describes a solid green light as Wi-Fi connected and the server reachable, and a blinking green light as still connecting or not reaching the server. If the light blinks for a long time, the mower is not getting through to the server, so look at the router first.
Bluetooth pairing and phone permissions
Pairing starts over Bluetooth, so the phone must be close to the mower and must have the right permissions. Sunseeker’s support guidance says to keep the phone within about 1 metre of the mower during pairing, to turn on Bluetooth on the phone, and to grant the app Bluetooth and location access in the phone’s settings. If this point matters for your setup, read our Mammotion app connection problems for more detail on it.
The startup password is the other common stumbling block. Some Sunseeker material lists 0000 as the default startup password. If you have changed it, use your own password. A wrong password usually produces a pairing error even when the phone and mower are close together, so check it before you repeat the steps.
Heads up
The default startup password and the screens in the app can differ between S4 firmware versions. Check the manual and the app version you have before you follow a step exactly.
Re-adding a mower that shows offline
When an S4 that worked before suddenly shows offline, a clean re-add usually fixes it. Sunseeker’s answer for its X3 model suggests a power cycle first, then removing the robot from the app’s device list and adding it back. The same sequence is a reasonable first try on the S4, although the exact screens may differ. You can find more background and practical detail on this point in our Dreame A1 app not-connected fixes. See our Anthbot app connection problems for further detail on a connected question.
- Power the mower off at the main switch. Wait about 30 seconds before switching it back on.
- Check the router. Confirm the network is online and running on 2.4 GHz.
- Remove the mower from the app. Delete it from the device list so the old connection does not interfere.
- Add the mower again. Follow the in-app setup, use Bluetooth pairing with the phone close by, and enter the Wi-Fi details.
- Check the light. A solid green Wi-Fi light means the mower is connected to the server.

When the app error does not match these steps
Sometimes the app shows an error message that none of the steps above covers. In that case, note the exact text, the time it appeared, and whether the mower’s own display showed an error code. Sunseeker publishes a list of error codes and app messages, and matching the text to that list is faster than trying random fixes. For a closely related angle, see our Worx Landroid app problems as well.
A mower that still will not connect after a clean re-add may point to a hardware or firmware problem. Sunseeker’s X5 manual says to contact the service center when the app still cannot reach the machine, and that is the right next step after you have ruled out the router, the phone, and the power cycle.
Checks before you contact Sunseeker
A support reply is faster when you can say what you already tried. Before you write, collect the model name, the app version, the Wi-Fi band you are using, the exact error text, and whether the phone is on the same network as the mower.
- Model and app version: the S4 and the app build decide which steps apply.
- Router band: say whether the network runs 2.4 GHz only or both bands.
- Light status: solid or blinking green, and for how long.
- What you already did: power cycle, re-add, and any permission changes.
Related reads: Related to this guide, you may also want to read our Sunseeker S4 hands-on review for a connected topic.
Frequently asked questions
Why does my Sunseeker S4 app say the mower is offline?
The usual causes are a router that is not on 2.4 GHz, a phone on a different network, or a mower that lost its stored connection after a router change. Check the band, put the phone on the same network, and power-cycle the mower before adding it again.
What Wi-Fi band does the Sunseeker S4 need?
Sunseeker’s support guidance says the router needs to run on 2.4 GHz. If your router combines 2.4 and 5 GHz under one name, check the settings to confirm the 2.4 GHz band is active.
What is the default Sunseeker startup password?
Some Sunseeker material lists 0000 as the default startup password. If you have changed it, use your own. A wrong password can cause a Bluetooth pairing error.
Is the Sunseeker V3 app the same as the S4 app?
The V3 may use a similar app setup, so the router band, same-network, and re-add checks are a reasonable starting point. Screens and settings can differ by model and app version, so check the manual for your mower before following a step exactly.
Sources
- Why can’t the robot connect to Wi-Fi? (Sunseeker support): the 2.4 GHz requirement, the same-network rule, and the connection checks.
- Sunseeker instruction manual (S3 EU) (Sunseeker): app setup and connection notes from the manufacturer manual.
01Up next7 min readLearnDreame A1 App: Fixing Connection and Offline ProblemsUpdated Nov 13, 2026
027 min readLearneufy E15 App: Fixing Offline, 4G, and Lifted AlertsUpdated Nov 13, 2026
038 min readLearnWhy Does My Robot Mower App Say Offline?Updated Nov 13, 2026
046 min readLearnEcovacs GOAT App Problems and How to Fix ThemUpdated Nov 13, 2026
057 min readLearnHusqvarna Automower App Problems and FixesUpdated Nov 13, 2026
067 min readLearnRobot Lawn Mower Problems: Causes and FixesUpdated Nov 13, 2026