Why Does My Robot Mower Smell Like Burning?
7 min read · by Rachel Whitman · Updated
Why does my robot mower smell like burning? Treat it as a safety problem first: stop using the mower, disconnect it, and do not charge it until it has been inspected. A burning smell can come from an overloaded motor, a battery fault, a short circuit, or blocked cooling vents, and some of these can lead to heat damage or fire. Some causes are simple to clear, but the electrical ones need a qualified technician, so do not try to find the source by running the mower again.
The short answer
- Stop and disconnect: switch the mower off and disconnect it as soon as you notice a burning smell.
- Do not charge it: the Euronics guide says to disconnect the mower immediately and not attempt to charge it.
- Clear the vents and deck: blocked cooling vents from grass and debris can make a blade motor overheat.
- Look for heat damage only once it has cooled: discoloured, melted or charred parts mean a professional inspection.
- Call a professional for a persistent smell: a smell that returns after cleaning is not a DIY fix.
Act first, then investigate
A burning smell is a warning to stop, not a problem to work through while the mower runs. The Euronics maintenance guide tells owners to disconnect the mower immediately and not try to charge it. Switch the mower off, move it away from anything flammable, and leave it to cool before you go near the housing or the battery.
Do not restart the mower to see whether the smell comes back. Repeating the test can make a fault worse, and it puts you at risk if a component is already hot or damaged.
Know the likely causes
The smell usually points to one of a few causes. Euronics lists a battery fault, a motor failure, or a short circuit, and says each needs professional diagnosis. Those are the serious ones. Less serious causes include a blade motor that is working too hard, usually because tall or wet grass has built up around it, and cooling vents that are blocked with debris. Write down any code on the display, because robot mower error code meanings help support staff identify the failing component quickly. Unusual sounds sometimes come before heat damage, and clicking noise causes can point to a worn gearbox or loose blade part. A swollen or hot pack is a known risk, and warning signs of a failing battery are described in detail in our battery guide.
The Mowrator troubleshooting page describes a blade motor overheating error with blocked cooling vents as the cause. Its suggested fix is to clean the deck and the vents. That is a sensible first check, but it does not replace an inspection if the smell has a strong electrical or plastic odour.

Clean the deck and vents when it is safe
Once the mower has cooled and is disconnected, look underneath and around the vents. Grass clippings, leaves, and soil can pack into the deck and the air openings, and they trap heat around the blade motor. Remove what you find with a brush or a cloth, and do not use water to cool a hot motor. A strained cutting motor can overheat, and blade motor error warnings often show up before any smell becomes noticeable.
Check that the blades and the wheels turn freely by hand. A blade or wheel that drags can overload its motor, and that extra load is one way a motor starts to run hot. If anything is stiff, seized, or wrapped in grass, clear it and check again before you consider using the mower.
Heads up
Do not open the housing or touch hot components to find the smell. Smelling near each motor can help narrow the source, but keep your hands away from hot parts and wait for the mower to cool first.

Look for heat damage, but do not repair it yourself
After cleaning, look for signs of heat damage: discoloured plastic, melted insulation, charred connectors, or a burnt smell that stays strong near one motor. These signs mean the affected part needs professional attention. The Euronics guide says that a swollen battery should not be powered on, and that any moisture inside the unit means it should be professionally serviced. Repeated lift or tilt warnings can come from a damaged chassis, so a recurring lifted error is another sign to inspect the housing.
Do not try to reuse a burnt motor or re-wire a connector to get the mower going again. Parts that have overheated can fail later, sometimes without warning, so replacing them is safer than repairing them at home.
When to call a professional
Get professional service if any of these apply:
- The smell continues after you have cleaned the deck and vents.
- You see melted plastic, scorch marks, or discoloured connectors.
- The battery is swollen, leaking, or hot to the touch.
- The mower shows moisture inside the housing.
- The smell comes from the battery or the charging contacts.
Tell the technician when the smell happens, whether the mower was working hard in wet or tall grass, and whether it was charging at the time. Those details help narrow the fault and can matter for a warranty claim.
What to do, in order
- Switch off and disconnect. Stop the mower and disconnect it as soon as you notice the smell.
- Do not charge it. Leave the battery alone until the mower has been inspected.
- Let it cool. Keep the mower away from anything flammable while it cools completely.
- Clean the vents and deck. Clear grass and debris, and check that the blades and wheels turn freely.
- Inspect for heat damage. Look for discoloured, melted, or charred parts, and for any swelling in the battery.
- Call a professional. If the smell continues or you see damage, book a service rather than running the mower.
Related reads: Record what the mower did before it stopped, since beeping and stopping mid-cut reasons often overlap with overload and overheating events.
Frequently asked questions
Is a burning smell from a robot mower dangerous?
It can be. A burning smell may come from an overheating motor, a battery fault, or a short circuit, and those can cause heat damage or fire. Stop the mower, disconnect it, and do not charge it until it has been checked.
Can I keep using the mower if it only smells after long runs?
It is safer to stop. A smell after long runs can still mean a motor is overloaded, often from tall or wet grass or blocked vents. Clean the deck and vents, let it cool, and check the blades and wheels. If the smell returns, get it inspected.
What does a blade motor overheating error mean?
The Mowrator troubleshooting page links this error to blocked cooling vents on the deck or blade motor, caused by debris or grass clippings. Its fix is to clean the deck and the vents. If the error or the smell keeps returning, contact support.
Can I cool an overheated motor with water?
No. Do not use water on a hot motor. Let it cool naturally, then clean and inspect it. Water near electrical parts can cause a short circuit and make the problem worse.
Sources
- Robot lawnmower troubleshooting and maintenance guide (Euronics): disconnect the mower immediately and do not charge it, battery fault, motor failure, or short circuit as causes, a swollen battery not to be powered on, and moisture needing professional service.
- Mowrator troubleshooting (Mowrator): the blade motor overheating error, blocked cooling vents, and the fix of cleaning the deck and vents.
01Up next7 min readLearnWhy Does My Robot Mower Keep Stopping at the Boundary Wire?Updated Nov 13, 2026
027 min readLearnWhy Does My Robot Mower Make a Clicking Noise?Updated Nov 13, 2026
037 min readLearnWhy Does My Robot Mower Drive Into the Flower Bed?Updated Nov 13, 2026
047 min readLearnWhy Does My Robot Mower Get Stuck Under Bushes?Updated Nov 13, 2026
057 min readLearnWhy Does My Robot Mower Start Mowing at the Wrong Time?Updated Nov 13, 2026
066 min readLearnWhy Does My Robot Mower Leave Tire Marks on the Dock Area?Updated Nov 13, 2026